Balluff BDD-06-1 Kurzanleitung

BDD-06-1
Display
Safety Notes
The Balluff BDD-06-1 display is
intended for use only with BTA
processors from Balluff, for which
connection to these displays is
permitted.
Tnaddition, the wiring notes in
•the user'sguide forthe respec-
tive processor must be followed.
Scope
This description is valid for the
BDD-06-1 display.
BALL-UFF
Digital Display
Fig. 1: Display BDD-06-1 (6 digits)
Technical Data
Display 6 digits, 7 segments, red
16 mm high
Connection 37-pin
SUB D connector
Data format
BCD code max. 20 Bit
binary code max. 16 Bit
Input level
Ot03V
Low
18t030V
High
Input resistance
PULL-DOWN > 10 kQ
Strobe signal min. 100 ns
low-active
Supply +24 V DC ± 20 %
Current draw ca. 80 mA
Dimensions, weight, ambient
DiN standard
Housing
96 x 48 x 107 mm
Dimensions
Installation depth ca. 160 mm
(with connector)
Mounting clips
Mounting
Weight ca. 400 g
Operating temp. Oto +45 oc
IP40 at front panel
Enclosure
Gebhard Balluff GmbH & Co.
Gartenstrasse 21-25
D-73765 Neuhausen/Germany
Phone (+49 71 58) 1 73-0
Fax (+49 71 58) 50 10
2
Function and Construction
The BDD-06-1 display is designed
for displaying the position which the
BTL transducer
sent to the BTA processor.
From the processor the data are
sent in parallel format to the display.
Control ihputs can select BCD Or
binary as the data format and deter-
mine the location
point.
The strobe signal controls updating
of the display value.
— Always when data arrives:
strobe input always Low
When strobe signal is received:
strobe input > 100 ns Low.
Wiring
The display is connected via the
data lines to the processor. Control
lines are used to determine
mal point position and the data
format. The signal on the strobe
input controls the updating of the
display value.
+24 V DC are needed to power the
display.
The corresponding wiring terminals
are found on the rear of the display.
Control lines
Pin Description
21 Decimal point
22 Decimal point
23 Decimal point
24 Sign
30 Strobe input
BCD/BIN toggle
31
Decimal point position
Pin 23 Pin 2
Low
Low
Low
Low
High
Low
High
LOW
High Low
High Low
BAUUFF
has detected and
of the decimal
the deci-
Pin 21 Decimal point
Low
none
xxxx x. x
High
xxxx.xx
Low
High xxx.xxx
x x. xxxx
Low
x. xxxx x
High
Installation
The display is typically mounted in a
panel cutout of approx. 43 x 91 mm
and secured using the clips supplied.
2
Pegel-
Anzeigespeicher
30
31
+ teil
35
Fig. 2: Block diagram of the
BDD-06-1
Data signals (parallel)
BCD
Pin
1 1
2
2
4
3
8
4
5 10
6 20
7 40
80
8
100
9
10 200
400
11
12 800
1000
13
2000
14
4000
15
8000
16
10000
17
20000
18
19 40000
20 80000
Supply voltage
Description
Pin
+24 V DC
35
GND
37
Display
binary
2
4
8
16
32
64
3
128
256
512
1024
2048
o
4096
8192
16384
32768
o
z