Frequently Asked Questions - Ispring Ed2000 Bedienungsanleitung

Where to Install ED2000
The ED2000 should be applied to the main water supply pipe through which water enters the
building. This will optimize the operation of ED2000 and ensure that the system conditions all
the water supplied to the building. If a water meter or grounding cable is used, installing the
ED2000 after the water meter or grounding cable is attached to the plumbing system is
recommended. The ED2000 can be used e ectively on galvanized and plastic water pipe.
ED2000 should be installed at least ten feet from any TV, radio, cordless telephone, or
electronic system to minimize possible interference.
How to Install the ED2000
Step1: Wrap the coils
Wrap the left antenna from the center to the left, starting under the water pipe. Wrap the
right antenna from the center to the right, starting over the water pipe. This ensures both
coils form counterclockwise circles against the water ow. Each coil is 55 inches (140 cm) long,
enough to wrap 12 times on the 3/4-inch pipe. A minimum of 7 wraps is required, and the
more, the better. Secure the wrappings with the included cable ties.
Step2: Mount the unit on the wall
Mount ED2000 on the wall. It could also be tied to a water pipe for convenience.
Step3: Plug in the power adapter
The LED lights should start ashing sequentially, indicating that ED2000 functions correctly.
Troubleshooting
Power Surges and Lockups
ED2000 water conditioner is designed to operate without interruption, providing years of
enhanced water quality. If your water quality seems to have changed, check the items below
to determine whether your ED2000 unit is functioning correctly.
To reset the ED2000, switch o the unit, wait for a few seconds, and switch on the power
supply. If you live in an area where power surges are frequent, it is recommended that you
07
Installation install a surge protector on the electrical outlet to which the ED2000 transformer is plugged
into.
Loose Antenna Wires
To transfer the energy into the water, the antenna wires must be held tightly against the pipe,
and the coils must be pressed snugly against each other. If the antenna wires are loose,
tighten them and retighten the wire ties. Make sure that the antennas are wrapped in the
correct direction.

Frequently Asked Questions

Functionality
Q: Does the ED2000 decrease the amount of calcium in my water?
A: No. ED2000 does not remove calcium from your water.
Q: Is the ED2000 e ective for severely hard water?
A: The ED2000 treats water with hardness as high as 425 ppm or 25 grains. For harder water, a
traditional water softener should be used in addition to the ED2000. For the best results,
the ED2000 should be mounted before the softener.
Q: Do I need more than one ED2000 for my home?
A:
One ED2000 is su cient for most homes, with 1 inch (25 mm) or less water mains. For
houses with water supply mains larger than 1" but less than 1.5" (38 mm), installing two
ED2000s side by side is recommended.
Q: Is there any e ect on water pressure due to ED2000?
A: Yes, the ED2000 can positively impact water pressure. Reducing scale buildup helps
improve water ow, which can lead to increased water pressure over time.
Q: What is the e ect of ED2000 on iron content in the water?
A: ED2000 does not impact the iron content of the water. For water with higher iron content
(above 0.30 ppm or 0.3 mg/L), an iron lter is recommended before the ED2000. iSpring
Water Systems has 1-stage, 2-stage, and 3-stage whole-house water lters that can be
equipped with iron/manganese lter cartridges.
Please contact us at +1 (678) 261-7611 or support@ispringwater.com for detailed
information.
08