XpertMatic MH-2000 Benutzerhandbuch

XpertMatic MH-2000 Digital Temperature Controller
XpertMatic
Thank you for choosing the XpertMatic MH-2000 digital temperature controller. The controller adopts the newest
heating and cooling technology and has a big range working voltage
over-temperature protection and an automatic temperature control system for various electric appliances such
as refrigeration and heating equipment. Please read thlS user manual thoroughly before use.
• Safety Notice:
- To prevent frequency interference, please do not bundle the sensor cable and your equipment cable together.
- The supply voltage must be consistent with the rated voltage. The voltage deviation is less than ± 10%.
- The temperature controller main body is not waterproof. Please do not place it in which there is moisture condensation.
- Please do not place the digital temperature controller where the children could reach.
• Specifications:
Working Voltage Range
Power Consumption
Standby Power Consumption
Temperature Control Range
Temperature &asurement
Temperature Control Precision
Slewing Range
Temperature Resolution
Temperature Sensor
Power Cable Length
Relay Capacity
Working Environment Temperature
Humidity
Dimension
• Buttons Instruction:
O Setting Button: Press 03 seconds g etintosettingmode, i t
will display: H Then press
cyclically. Please press Oor Oto set the value you
chose. After setting, press
O Reset Button (Under Setting Status): Press O button
once to save the setting, exit the setting mode and back to the
Display Status.
O or O Button: Pressthe up/downbutton to increase/decrease
the value. Long press the button to increase/decrease the value
quickly.
• Setting:
I-Eating Mode: Press0 3 seconds to go into setting mode,it will show
o choose "K. After 3 seconds, it will save automatically and go into heating mode, e.g. the control
H
temperature is 40'F, the slewing range is 2'F, and the delay time is 2 minutes. When the environment
temperature2control
environment temperature$8"F
will turn on in 2 minutes.
CoolingMode:Press 0 3 seconds to gointosettingmode, i t willshow
choose "C". After 3 seconds, it will save automatically and go into cooling mode, e.g., the control
temperature is 40'F, the slewing range is 2'F, and the delay time is 2 minutes. When the environment
temperature S400F, the cooling equipment will turn off automatically. When the environment
temperature2420F (400F+20F=420F),the cooling equipment will turn on in 2 minutes
Control Temperature Setting: Press 0 3 seconds to gointosettingmode, i t willshow H
O once to go to
The temperature will save automatically in 3 seconds. (Temperature Range: -40+212•F).
Dela y Start S etting: Press3seconds
. Longpressthe button O Or O set the delay time that you prefer.The delaytime
to go to
will save automatically in 3 seconds. (Delay Start Time Range: 0-10minutes)
p Skwing Range Setting:Press 0 3 seconds to gointosetting mode, it willshow
a 5 times togoto
slewing range will save automatically in 3 seconds. (Slew Range: 0.1 -SOOF)
• An example of heating mode:If you want to keep your roomfrom 70T to BOOF
Press 0 3 seconds to
• An example of cooling mode:If you want to keep your room from 70T to
Press 0 3 seconds to
Press the button O to
choose
Heating Mode: RI-P3 80-10=70dF (&ating device turns on S7(YF, shut in BO'F)
cooling Mode: P1+P3 70+102800F (cooling device turns on 2800F, Shut in 700F)
• An exampleof setting the delay start time: If you want to set the delay Start time to 1 minute
Press 0 3 seconds to
Defective Prompt:
If the temperature exceeds the upper limit of 2120F, "HHI-r flashes and the device switches off: if the temperature
is below -40"F, "LCL" flashes
• Warranty:
XpertMatic guarantees 60 days no reason replacement or refunds from the day you purchase. We provide a 2-year
warranty and provide lifetime technical support Please reach us via
a member in
User Manual
Accuracy
O onceto goto thenextsetting H
to save and return to Display Status,
temperature (400F), the heating equipment will turn off automatically. When the
(control temperature 40+ - slewing range 2f-), the heating equipment
Cong press the button O or O set the control temperature that you prefer.
. Longpressthe button O or O to set the slewingrangethat you prefer.The
80.1}
PressO onceto go to 3?
Long press the button ot
set the temperature to 800F.
PressO onceto go to
Long press the button O
set the temperature to 70•F.
Press0 2 times to goto
Press the button O to set the
delay time to 1 minute.
and the device switches
to get an extra 60 days no reason replacement.
AC 90V.250V
S3W
-40+-212*
±O.B'F
0.1 OF-500F (Adjustable)
O.IOF
NTC
4.9ft
IOA/AC 220V
-300+150*
goo,'0RH (NOcondensate)
6.1X2.4X1.1 in
Setting
Button
Reset
Button
togointo setting mode, itwill s how m press 0 2times
off
50/60Hz). It can be
50/60HZ
(4.9ft)
AC 90-250V
Environment
Temperature
O- Increase
Decrease
Control
Temperature
Tempeture
Sensor
. Press button
Press button O or
Press
Press o 2 times to go to
Long pressthe button O to
set the slewing to IOaF.
Press the O button once to
save the setting.
10.0
Press0 2 times to go to
Longpressthe button O to
set the slewing to IO'F.
Press the O button Once to
save the setting.
70.1}
Press the O button once to
save the setting. The heating/
cooling device will turn on in
1 minute after reach the control
temperature±slewing value.
You can register as
or
Press
3