D-Parts Fontastic Limbo Bedienungsanleitung

BT LED Speaker
User Manual
Dear customer,
thank you for purchasing this wireless LED Speaker. Please read these operating instructions
carefully and follow the instructions and tips to get the most out of your Speaker.
Package Contents
• Bluetooth' Speaker Limbo
• Micro-USB charging cable
• Line in audio cable
• Carabiner hook
• User Manual
If any of the above pieces is missing, please pack the product again and bring it back
to your dealer.
Overview
1. LED lighting
2. Next track / Vol+
3. Multifunction Button / Start- Stop Musik
4. Previous track / Vol-
5. Mode button (M) *AUX <-> Bluetooth*
6. Silicone Cover
7. LED red (charge indicator)
8. Micro-USB Charging port
9. 3.5 mm Audio socket
10. Loop for carabiner hook
11. Carabiner hook
M
Getting started
Charging the battery
Limbo is equipped with an internal rechargeable lithium-lon battery. Open the silicone cover on
the back Of the device (6). Connect the Micro USB cable with the micro USB charging port (8) Of
the Limbo. The cable can be connected to a computer or a standard USB power adapter. The red
LED of Limbo (7) lights up while charging. The normal charging time is 3,5 hours. The red LED
turns off when fully charged. The cable can be disconnected.
Note: Charge Limbo for at least 2.5 hours before initial use.
Switching On IOff
To turn on the speaker, press and hold the multifunction button (3) for about 3 seconds.
To turn off the speaker, press and hold the multifunction button (3) for about 3 seconds.
Pairing
Limbo must be paired with a Bluetooth@ device before use.
This is a two part process; one part is carried out on the Speaker and the other is carried out on
the other Bluetooth' device.
Note: Please note that different mobile phones may require different pairing methods.
1. Turn on the speaker by pressing the multi-function button (3) and holding for approx. 3
seconds. An acoustic signal sounds twice in succession. This indicates that the Speaker is in
pairing mode.
2. Use your mobile phone, computer or another Bluetooth@ transmitter in order to search for
BluetoothS audio devices.
3. The Bluetoothn device should indicate that it has found „Limbo".
4. Confirm pairing with Limbo. Enter „OOOO"if you are asked for a pairing code.
If you are unsure about the pairing procedure Of your Bluetooth' device, please check your
device manual.
If using a Bluetooth@ transmitter without display, set it to pairing mode and wait a few seconds
until the connection with Limbo is established.
Note: If the connection is lost or the transmitter is temporarily disconnected,
tries to restore the connection.
Music playback
Music playback via Bluetooth@
Start music playback on the Bluetooth' source which is paired with the Limbo. The music is
transferred to the Limbo. Stop the music playback on the Bluetooth@ source to interrupt the
streaming.
Note: The device must support the A2DP profile for music streaming. Redial is deactivated during
music playback.
Music control
TO play or stop music playback, briefly press the Start/St0p button (3).
To skip to the previous track, press the Previous track button (4).
TO skip to the next track, press the Next track button (2).
Note: The phone must support the A2DP and AVRCP profile to play and control music via
Bluetooth.
Music Playback via Line in
1. Open the silicone cover (6) on the back Of the Limbo. Connect the device
from which the music should be played with the included
Audio cable with the 3.5 mm audio connector (9) of the Limbo.
2. Switch on the limbo. Briefly press the mode button (5) once to enter the line-in mode.
3. Now the music is output via the limbo.
WC
Limbo automatically
TechnischeÄnderungenvorbehalten / Fontastic,by D-PartsMobilphon& ZubehörGmbH• Birkenweiherstr, 1 6 • 63505 Langenselbold, G ermany/V2_04 20
„
Limbo"
Note: When using the wired connection, the keys have no functions.
Use the audio source to control the music.
Hands-free features
With its built-in microphone and intelligent noise reduction, the Boogie is perfectly suitable for
phone calls.
Answerlend/reject calls
To accept an incoming call, briefly press the multifunction button (3).
TO end a call in progress, briefly press the multifunction button (3).
TO reject incoming calls, press and hold the multifunction
Redial
In standby mode, press the multi-function button (3) twice in a row to activate this function.
The connected phone redials the last number.
Adjusting the Volume
To increase the volume, press and hold the Next track button (2) until the desired volume is
reached.
To decrease the volume, press and hold the Previous track button (4) until the desired volume
is reached
LED lighting:
After switching on the Limbo, the effect LED lights up in changing
this function, briefly press the LED lighting button (1).
LED Demo
Press the LED lighting button (1) for approx. 3 seconds when switched Off.
The effect LED lights up in changing colors and switches off automatically after 10
seconds.
Technical Data
• 4.1
• Range: up to 10m
• Profile: HSP, HFP, A2DP, AVRCP
• BT Frequency: 2.402-2.480GHZ, 2.4G
• mm Audio Line-ln
• Input Power: 5V DC
• Internal Microphone
• Micro USB charging port
• Charging time: 3,5 hrs.
• Operation time: 24 hrs.
• Dimensions: 124 x 65mm (HxB)
• Weight: 204 g
Safety advice:
• Do not open the device
• Do not hold the device under water
• Keep it safe from humidity
• Do not connect the adapter to the device by using force
• Keep the device away from children
• Disconnect electronic devices from the power when not using them for longer time.
• Do not use the device when it has visible
In case you need technical support, please contact our support-team by e-mail under
service@fontastic.eu.
Registration and Safety
Certification/General Information
We hereby declare, that this device carries the CE mark in accordance with the regulations and
standards. It conforms with the fundamental requirements of the RED 2014/53/EC, EMC
directive 2014/30/EC as well as the Low Voltage Directive 2014/35/EC. wow.d-parts.de/konfo
Note on environmental protection:
After the implementation of the European Directive 2012/19/EC in the national legal
system, the following applies: Electrical and electronic devices may not be disposed of
with domestic waste. Consumers are obliged by law to return electrical and electronic
devices at the end of their service lives to the public collecting points set up for this
purpose or point of sale. Details of this are defined by the national law of the respective country.
This symbol on the product, the instruction manual or the package indicates that a product is sub-
ject to these regulations. By recycling, re-using the materials or other forms of utilising old devices,
you are making an important contribution to protecting our environment.
GB
button (3) for 2-3 seconds.
colours. To deactivate
defects.