yellow jacket TITAN Besitzerhandbuch

TITANO Test and
Charging Manifold
PROCEDURES
The various service and testing procedures
be performed after the manifold gauge set has been
installed as shown in the following diagrams.
00
(2)
O'SC HARGE
CORE TOOL
l. TO PURGE HOSES II. TO OBSERVE
BEFORE HOOKING UP PRESSURES
Connect hoses at
E & F; Do not tighten
Close valves
4 Connect hose G to
refrigerant
Open valves
Crack D & G valve to
Ill. TO CHARGE
begin purge
TION SUCTION
SIDE WITH
Tighten hose
Over-pressuring the gauge voids warranty
[Vil YELLOW
I.E JACKET@
OWNER'S MANUAL
Due to the unusually high pressures and hazardous
gasses used in refrigeration and air conditioning,
only TRAINED refrigeration and air conditioning
technicians should use this equipment.
procedures must be used.
Section 608 of the Federal Clean Air Act requires
that all persons who maintain, service, repair, or
dispose of appliances must be certified
vember 14, 1994. Failure to comply can cost you
and/or your company as much as $25,000 per day,
per violation. The EPA also offers a reward up to
$10,000 for providing information concerning
violations to the Act.
Key:
No flow in hose
Closed
below can
Open valve
Flow in hose
2
(2)
FRO
POMP
PUN P
CORE REWhAL
CORE R*MOVAL TOOL
•V. TO CHARGE
OPERATING
REFRIGERATION
SUCTION (VAPOR) SIDE
Close valves
Purge as in I
Close valves
4 Connect
Connect hoses as
refrigerant
illustrated
Open valve
Crack open back
seat Close valves
D Open valve and
REFRIGERA-
throttle
(VAPOR)
F Crack front
SCHRADERS
Purge as in I
Charge as in IV
PROCEDURES,
Proper
CORE REMOVAL
VI. TO SET LOW SIDE
Disconnect pressure control line.
since No
union into control
B, C & D Close
Open valve
Back seat then crack open
Back seat F
Open to regulate pressure;
valve
O
REMOVING THE
After completing service operations, you must remove the manifold from the system without losing
refrigerant or admitting air.
Close valves E & C.
Then open manifold valves A, B and D, 1/2 turn
Close valve F
This arrangement will move all the high-pressure
gauge and put it into the low side. Close all manifold valves and remove hoses.
PARTS LIST
41042
41142 (x4)
hose G to
41134 (x4
41133 (x4)
41131 (xl
41041 (x2)
seat
YELLOW JACKET* Products
Ritchie Engineering Company,
10950 Hampshire Avenue
Bloomington, MN 55438-2623
cont.
v. TO PULL VACUUM
Close valve
D
Connect hose 3 to pump
c Open valve
A & B Open valves
E & F Mid position valves
DISCHARGE
Note: To improve pull down
minimize restrictions), and use minimum 3/8"or larger hose.
sucT10N
TOOL
CONTROL BUILD UP PRESSURE
Using flare union, screw
line and other end of hose I
valves
set control
MANIFOLD FROM THE SYSTEM
refrigerant from the line and the high-pressure
49192
41113
191
1135 (x4)
1 (x3)
1047 (x2)
1046
70 (xa)
4113
Div.
Inc.
South
Printed in U.S.A. P/N 500750 RevF
#18975
time, use core removal tool (to
o.
2
3
E
DISCHARGE
CORE REMOVER
41142
41133 41134
41135
41041 YELLOW
41042 BLUE
41044
RED
Phone: 952-943-1333
Fax: 1-800-322 8684
Int'l Fax: 952-943-1605
e-mail: custserv@yellowjacket.com
Web Site: www.yellowjacket.com