Orno Adviti RIGEL LED Bedienungsanleitung Seite 3

RIGEL LED Set of work light with tripod and adapter
EN
Operating instruction
Directions for safety use
Before using the device, read this Operating Instruction and keep it for future use. Any repair or modification carried out by yourselves
results in loss of guarantee. The manufacturer is not responsible for any damage that can result from improper device installation or
operation. Installation of the device should be carried out by an experienced person familiar with the relevant installation regulations in
force in the country concerned or by an electrician. In view of the fact that the technical data are subject to continuous modifications, the
manufacturer reserves a right to make changes to the product characteristics and to introduce different constructional solutions without
deterioration of the product parameters or functional quality. Additional information and technical support related to the product is
available at www.adviti.pl. Orno-Logistic Sp. z o.o. holds no responsibility for the results of non-compliance with the provisions of the
present Manual. Orno-Logistic Sp. z o.o. reserves the right to make changes to the Manual - the latest version of the Manual can be
downloaded from support.adviti.pl. Any translation/interpretation rights and copyright in relation to this Manual are reserved.
1. Do not immerse the device in water or another fluid.
2. Do not cover the device during its operation.
3. Do not operate the device when its housing is damaged.
4. Do not open the device and do not repair it by yourselves.
5. Do not use the device contrary to its dedication.
6. The chipped globe, screen or protective shield must be replaced immediately.
7. The minimal distance of a light fixture (its light source) from the spots and objects that it's illuminating.
8. Risk of electric shock.
9. Product not suitable for covering with heat-insulating material.
10. Product compliant with CE standards.
11. Protection class II.
12. The product is suitable for indoor use.
13. Do not look at LEDs directly from up close.
14. The product is not compatible with lighting dimmers.
15. Each household is a user of electrical and electronic equipment, and hence a potential producer of hazardous waste for humans and
the environment, due to the presence of hazardous substances, mixtures and components in the equipment. On the other hand, used
equipment is valuable material from which we can recover raw materials such as copper, tin, glass, iron and others. The WEEE sign placed
on the equipment, packaging or documents attached to it indicates the need for selective collection of waste electrical and electronic
equipment. Products so marked, under penalty of fine, cannot be thrown into ordinary garbage along with other waste. The marking means
at the same time that the equipment was placed on the market after August 13, 2005. It is the responsibility of the user to hand the used
equipment to a designated collection point for proper processing. Used equipment can also be handed over to the seller, if one buys a new
product in an amount not greater than the new purchased equipment of the same type. Information on the available collection system of
waste electrical equipment can be found in the information desk of the store and in the municipal office or district office. Proper handling
of used equipment prevents negative consequences for the environment and human health!
Intended use/purpose
The RIGEL LED is a complete light set that includes a folding 5-wing work light, an adjustable tripod and a movable adapter. The set offers
a strong 55W light source suitable for use in various places such as the workshop, basement, garage or construction site. The folding work
light is equipped with 6 LED light sources - 5 movable side wings and one round LED panel in the center. The wings can be easily regulated
within the range of 90°, adjusting the required angle of light to precisely illuminate the work area. Additional advantage of the work light
is that the wings can be folded, making it easy to carry or store the lamp. The adjustable tripod gives you the ability to adjust the height of
the lamp according to your preference, and the movable adapter allows you to change the direction of the light within 180°. This is an
extremely convenient solution that allows you to adapt the direction of the light as you work. Mounting the lamp is intuitive and quick
thanks to the included adapter with E27 thread - simply screw the lamp into it. A 2m power cord makes it convenient to use.
Installation
1. Make sure the main power supply is turned off before installation.
2. Screw the E27 thread adapter to the tripod.
2. Screw the lamp into the bulb thread (take care not to tighten the lamp too much).
3. Adjust the position of the lamp to suit your needs:
- adjust the lamp wings according to the desired light angle (adjust each lamp wing in the range of 0-90°),
- adjust the tilt of the lamp with a movable adapter (adjustable up to 180°)
- adjust the height of the tripod (from 68cm to 210cm)
4. Turn on the power and test the operation of the device.
Technical data
Nominal voltage: 230V~, 50Hz
Light source: LED, non-replaceable
Power: 55W
Luminous flux: 4950lm
Color temperature: 6500K
Light color: cool white
Color rendering index Ra/CRI: >80
Safety and maintenance
Any maintenance shall be carried out after the power source has been switched off. Clean with dry and delicate cloths only. Do not use
chemical cleansers. Do not cover the product. Provide free air access.
Lifespan L70/B50: 50 000h
Ingress protection: IP20
Lamp material: plastic
Tripod material: steel + plastic
Dimensions of the unfolded lamp: 330 x 145 x 330mm
Tripod height: 68-210cm
This product contains light sources of energy efficiency class F.
3