Seite 1
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. USA:cs.us@costway.com POL:sklep@costway.com If you're having difficulty, our friendly AUS:cs.au@costway.com DEU:cs.de@costway.com PLEASE READ AND KEEP FOR FUTURE REFERENCE. customer team is always here to help. GBR:cs.uk@costway.com FRA:cs.fr@costway.com I T A :cs.i t @costway.com ESP:cs.es@costway.com...
Before You Start Avant de Commencer Please read all instructions carefully. Veuillez lire attentivement toutes les instructions. Retain instructions for future reference. Conservez les instructions pour vous y référer ultérieurement. Separate and count all parts and hardware. Vérifiez toutes les pièces et les accessoires. Read through each step carefully and follow the proper order.
Prima di Iniziare Voordat U Begint Si prega di leggere attentamente tutte le istruzioni. Lees alle instructies zorgvuldig door. Conservare le istruzioni per riferimento futuro. Bewaar de instructies voor toekomstig gebruik. Separare e contare tutte le parti e gli accessori. Scheid en tel alle onderdelen en hardware.
Seite 7
An x8 An x8 An x7 x117 x109 x109 Bn x4 Bn x2 6*30mm 300mm Bn x2...
Seite 8
DE: Hinweis: Lösen Sie zuerst das weiße Kunststoffteil. Nachdem Sie den Bolzen in der Platte installiert haben (das weiße Kunststoffteil sollte vollständig in der Platte eingebettet sein), ziehen Sie den Bolzen an, um ihn an der Platte zu befestigen. Bn x2 FR: Remarque : Desserrez d'abord la partie en plastique blanc.
Seite 9
An x6 Bn x6 C x3 An x6 A x2 An x2 Bn x2 C x3 Bn x4 An x6 G x1 An x4 An x6 An x2 An x2 C x2 EN: Note: Loosen the white plastic part first. After installing the bolt into the plate (the white plastic part should be completely embedded in the plate), then tighten the bolt to fix it on the plate.
Seite 10
DE: Hinweis: Lösen Sie zuerst das weiße Kunststoffteil. Nachdem Sie den Bolzen in der Platte installiert haben (das weiße Kunststoffteil sollte vollständig in der Platte eingebettet sein), ziehen Sie den Bolzen an, um ihn an der Platte zu befestigen. G x1 An x6 FR: Remarque : Desserrez d'abord la partie en plastique blanc.
Seite 11
Ao x4 Ao x4 P2 x8 P1 x8 Ao x4 N x4 P1 x2 Ao x8...
Seite 12
N x9 P2 x3 N x4 P1 x2 N x3 P2 x1 P2 x1 Ao x6 N x3 N x9 P2 x3...
Seite 19
EN: Firstly, remove the dust from the mirror surface. Then peel off the adhesive on the back of the light bulb. Stick the light bulb to the corresponding position on the mirror. Rotate the light bulb to adjust the wire length between two adjacent light bulbs. Finally, pass the USB interface through the wire hole of board ②...
Instructions De Retour / Réclamation De Dommages Return / Damage Claim Instructions NE PAS jeter la boîte/l'emballage d'origine. DO NOT discard the box / original packaging. Dans le cas où un retour est requis, l'article doit être retourné dans sa boîte In case a return is required, the item must be returned in original box.
Seite 23
Istruzioni Per La Restituzione / Reclamo Per Danni Instructies voor Retournering/Schadeclaim NON scartare la scatola / confezione originale. GOOI DE doos/het originele verpakkingsmateriaal NIET weg. Nel caso in cui sia richiesto un reso, l'articolo deve essere restituito nella scatola In het geval van een retournering moet het artikel in de originele doos originale.