Installation And Use; Disassembly And Disposal; Technical Data - Outwell Moonstone Stringlight Lantern Bedienungsanleitung

UK: INSTRUCTION MANUAL
1. Lantern
2. Light string with attachment hook
3. Flashlight
4. Power button
5. Protective lid
6. Hanging hook
7. Magnets
8. Charging indicator
1.

1. Installation and use

1.1 Light modes:
1) Press the power button (4) located underneath the lantern to turn it on.
2) Press the power button again to toggle through the light modes.
The lantern has 5 light modes:
a. Light string (constant)
b. Light string (blinking)
c. Light string (pulsating)
d. Light string (constant) + lantern (medium) combined
e. Lantern (strong)
3) Press the power button again to turn the lantern off.
4) Press and hold the power button for 2 seconds to turn on the flashlight (3) located underneath the
lantern. Press the power button again to toggle through the light modes.
The flashlight has 3 light modes:
a. Flashlight (strong)
b. Flashlight (medium)
c. Flashlight (SOS)
1.2 Use of the lamp:
• The lantern is charged using a 5V DC USB power outlet. The USB-C input is located under the
protective lid (5) underneath the lantern.
• A charging cable is included with the lantern. The charging time from empty to full is approximately
1.5 hours.
• Please fully charge the lantern before first use.
• The charging indicator (8) indicates the battery status while charging and when the lantern is
turned on.
• The lantern (1) can be used standing, hanging from the hook (6), attached to a magnetic surface
using the magnets (7), or as a handheld flashlight (3).
• Pull the light string with attachment hook (2) to extend it, pull it through or around different
hanging points and fasten the attachment hook in the light string, lantern hanging point or a
similar fixture. The light string can be rolled in by turning the hanging hook (6) clockwise.
• Lantern is water resistant to IP44.
• Do not stare directly into the light source, as this can be harmful to the eyes.
2
7.
6.
8.
3.
7.
5.
7.
4.
2.
UK: INSTRUCTION MANUAL
2. Cleaning and maintenance
The Lantern can be cleaned with water or a damp cloth.
Do not use corrosive liquids to clean the lamp, as this may cause damage.
3. Light Source: LED
Light source and control gear are non-replaceable.
This design prevents the introduction of weak points in the
construction that could reduce the product's lifespan.

4. Disassembly and disposal

Instructions for disassembly of lamp for disposal of components
when the lamp has reached the end of its usable life:
Disassembly: Use a flathead screwdriver or similar tool to carefully insert it into the seam between the
top cap (black portion) and the lampshade (white portion). Gently pry apart the two components to
separate the top and bottom parts of the lamp. Dispose of the plastic components (lampshade and top
cap) in accordance with local regulations for plastic recycling.
Battery removal: Once disassembled, locate the internal battery by cutting any wires securing it.
Use appropriate tools to detach or cut the wires connected to the battery. Dispose of the battery in
accordance with local regulations for hazardous waste or battery recycling.
PCB, LEDs, and electrical components: Unscrew any screws holding the PCB board, LEDs, or other
electrical components in place. Cut the wires connecting these components and remove them. Dispose
of all electronic components, including the PCB board, LEDs, and wires, in accordance with local e-waste
disposal regulations.
Metal parts: Remove any metal parts, such as screws, and dispose of them according to local
regulations for metal recycling.
Final disposal: Dispose of any remaining components or materials in accordance with local regulations,
ensuring that all parts are separated and sorted according to their material type (plastic, metal,
electronic, etc.).

5. Technical data

3.7V , MAX 5.0W
Battery: 3.7V , 1500 mAh Li-Ion
USB Input: 5V , 1.0A
Class 3 appliance
Degree of protection:
The product is waterproof to IP44
3