OMNISTOR OMNIVENT Kurzanleitung

Readthese instructionscarefully. No guaantee will be allowed
for wrong installation.
INSTALLATION AND USE OF THE ROOFLIGHT
CONTENTS MOUNTING
Screw OIN 7981 - x
washer DIN • MS
screw DIN 1982 x 38
Mounting dip.
saew DIN 7981 x 32 —
Operatingknob with square shaft 6 x 70 mm.
Extension tube
INSTAUAIK)N ROOFUGHI (fig.l)
TO instdl the OMNIVfNIa '00t
the OMNIVENT12V (with ventilatm) a thickness of
required.
1. Make a 400 x 400 mm hole and cleanthe sutroundngs (figQ).
2. Put acid free sealing materia' that sticksto A.BS. undet the edge of
the upperframe (C)(fig. 3).
3. theupperpart with thehingein thedriving(flection.
4. fix the exterior frame to the roof by usrnga mountinq clip in the
middle of each side (see fig. 5), Usescrew DIN7982 -
length accordingto the table- Donot tighten too "Wth, so that no
deformation Ot the frame tan OCCUt.
S. for OMNIVENT12V, with ventilator
of the ventilator as described below
6. Put the operating knob with the squue shaft into the inner frame and
secureit with the O-ring(fig. 9).
Remark:Thedelivered operatingknob with squareshaft is suitablefor
roofthicknessesfrom 2Sup to 50 mm. For a roofthicknessover 50 mm.
use the kit for roof thickness40•60rnm with a squareshaftot 90 mm
length.
7. Install the inner frame (E) with the squarestuft (D) of the knob in the
hole of the mecanism Fora 100fthickness 2 40mm. put first on the
screw tube in each comer of the exteli01 frame (C) an extension tube
Thiswitl rnakethe saewing of the interiot frame easier (fiq. 7).
8. Fixthe interior frame to the exterior frame in the cornels by usingthe
screws DIN7981 • 4,2mm with length accordingto the table (fig. 6),
9. Clipsthe flynet (F) inside the frame. (The OMNIVENT 1 2Vmth fan has
has an integrated flyscreen).
10. cups the roller blind (G) on and secure it with 2 screws
32 (fig 4).
USE ROOf11GHr
• Close the lid before driving
• Totake away the roller blind. unscrewand take off.
OPTIONS
-12Vtan Prodrø.
• 12V fan With thennostat. PfOdnr, 23
• Kit roof thickness 40-60rnm, Prod. or. 23 0200 00.
10
13
Of25 to 60 mm is fewited, For
to 60 mm is
rnm with
connect DCto the lead-tn wiles
7981 x
00.
,'IVY)
FAN setE0
INSTALLATION AND USE OF THE VENTILATOR
INSTALLATION Of THE VENTILATOR
Aventilator 12V• 20 min'/min (700 cft/rnin.)
afterwa/ds to the OMNIVENI r ooflight
1,nx the ventilator(B)to the outerframe(C)by screws
10).Jo allow to insert the 2 screwsat the frontside.open the lid for
about 5 cm, unscrewthe hinge profile and slide the lid backwards.See
fig. u.
2. Connect 12V DCto the lead-in wires 01 the ventilat0' via a slow fuse of
IOA in the • conduction. Theconnect01 can be stored in the chanter
neat the operating device(fig. 8). Forthe fan with continuous speed
regulation: red wire: positiveO, black wire: negative O.
Providedthe wiring is done correctly,the installation will meet EMC
standards89/336/EEC. Thefan has approval KBAno, 19303for
installation on vehicles
USE OF3 SPEEDS VFNIUTOP(fig. 13)
- Theventilatot is started by the switch SS
- Theairflow is adjustedby usingthe switch 56 [2 1 3]:
' position 1 'm3/min. (24S cft/min.) (10 W •
' position2 • 12 m3/rrün.(420dt/min.) (25 W• 2.2A)
• position 3 20 m3/rrin. (700 dt/min.) (60 W - 5 A)
Rernuk
Donot start jrnmediately at the hiftst
blown by the high current peak (ISA).
USE Of THE WITH CONONUOUS SPEED REGULATION AND
(fig. 14)
• Thefan is tutned on and ofl by using the switch 52 [011.
• me fan is set on 'extract' ot 'intake' by usingthe switch Sl
Thespeed canbe regulated continuously b y means of thesmall53
button
• MIN. - 3rnb'rnin. (100
• MAX. 20 ms/rr»n. (700 cft/min) (60 W • SA).
• Theswitch temperattne 01the thermostat can be determined by the
small S4button. it can be set continuouslybetween IS•
650 (pos. Position correspondsto a 2S to 30' Ctemperature.
Whentheptoggammed t ernpetature isreached, the fanautomaticdly
switches on (provided that the SwitchS?is in position 1).
• Put the small thermostatbutton 54 in position Oto plevent the
operation ot the thermostat. In trus position the fan
temperatures below ISOC
In longer absence.programm the fan at reducedspeed when usinqthe
thejmostat. lhe risk ot an empty battery Will be avoided.
MAINTENANCE
rhe ventilatof grid be taken Offfo' cleaning.
THERnSTAT FAN SPEED
0
14
be installed
x 25(fig.
O•l: or "extract" or Eintake•.
A)
speed level- Thefusecould be
O
(pos. 1) and
be used in
11
12
ON-OFF