Herunterladen Inhalt Inhalt Diese Seite drucken

SmartPool Nitro Bedienungsanleitung

Automatischer poolreiniger
Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 25
INSTALLATION
• Place the power supply in an area that will allow the cleaner to cover all areas of the pool.
• Be sure to only plug the power supply into a GFI (ground fault interrupter) or ELI (earth leak interrupter) protected electrical outlet.
• Look at the power supply and check that the power supply switch is in the off position.
• Plug the power supply into the protected outlet.
• Plug in the connector from the cleaner into the power supply. The connector is keyed so that it will only plug into the power supply one way.
Make sure that the plug is pushed all the way onto the power supply. Slide the connector lock (strain relief) onto the connector and turn
the connector lock clockwise until it is snug.
OPERATING THE CLEANER OUT OF THE WATER WILL DAMAGE THE MOTORS AND VOID THE WARRANTY
• Place the cleaner into the pool and if needed rock the cleaner side to side to release any trapped air. The cleaner will sink to the bottom of the pool.
• Put enough of the blue cord into the water to assure that the cleaner can easily reach all areas of the pool.
• Turn the switch on the power supply to the on position.
• The cleaner will begin its cleaning program.
• The cleaner will automatically shut itself down after two hours.
• If a second cleaning is required or the unit is accidentally shut off, you should wait one minute before switching the unit on again.
IMPORTANT NOTE: During normal operation, the cleaner will appear to shut off for a few seconds, raise the
front wheels off the pool bottom and move either left or right or turn for an undetermined amount of time. This is
normal and has been preprogrammed into the unit to assure the quickest and most efficient cleaning of your pool.
NITRO ROBOTIC POOL CLEANER OPERATION MANUAL
Congratulations on your purchase of the most technologically advanced automatic pool
vacuum available today. The Nitro is easy to use and will make maintaining your pool
affordable and effortless. Following these simple directions will insure that the Nitro will
quickly and efficiently clean your pool today and for many years to come.
DO NOT RUN THE CLEANER OUT OF THE WATER.
Inhaltsverzeichnis
loading

Inhaltszusammenfassung für SmartPool Nitro

  • Seite 25 Poolreinigers. Der Nitro ist einfach in der Handhabung und macht die Wartung Ihres Pools bezahlbar und mühelos. Die Befolgung dieser einfachen Regeln stellt sicher, dass der Nitro Ihren Pool heute und für viele weitere Jahre schnell und effizient reinigt. INSTALLATION •...
  • Seite 26: Wichtige Sicherheitsanweisungen Alle Anweisungen Lesen Und Befolgen

    WICHTIGE SICHERHEITSANWEISUNGEN ALLE ANWEISUNGEN LESEN UND BEFOLGEN GEFAHR: Gefahr eines Stromschlags oder Todes durch Stromschlag – Die elektrische Leitung dieses Produktes muss gemäß des National Electrical Code (Nationale Elektrische Vorschriften) und aller anwendbaren örtlichen Vorschriften und Bestimmungen installiert werden. Unsachgemäße Installation führt zu elektrischer Gefahr, die bei Poolbenutzern und anderen durch Stromschlag zu Tod oder schwerer Verletzung führen und auch Schaden an Eigentum verursachen kann.
  • Seite 27: Den Reiniger Aus Dem Pool Heben

    DEN REINIGER AUS DEM POOL HEBEN • Halten Sie den Verschlussdeckel wie in Abb. 4 gezeigt und ziehen Sie an der Klemme mit der Markierung „PULL TO REMOVE BAG“ („ziehen, um den Beutel zu entfernen“). • Ziehen Sie langsam am blauen Kabel, um den Reiniger an die Oberfläche sowie den Rand des Pools zu holen.
  • Seite 28: Lagerung Im Winter

    Beginnen Sie mit dem Teil des Filterbeutels, auf dem das Wort „PUSH“ Während Sie Ihren Nitro anwenden, kann es sein, dass sich das Kabel anfängt aufzuwickeln. (drücken) zu lesen ist und drücken Sie den Filtersaum in die Öffnung, sodass die Das übermäßige Aufwickeln kann zu Einschränkungen bei der Poolreinigung führen.
  • Seite 29: Hilfe Zur Fehlerbehebung

    HILFE ZUR FEHLERBEHEBUNG PROBLEM MÖGLICHE GRÜNDE LÖSUNGEN Wasser ist in den Antriebsmotor gelaufen Wechseln Sie den Antriebsmotor GERÄT BEWEGT SICH NUR WENIGE ZENTIMETER VOR UND ZURÜCK Verschmutzungen blockieren das Antriebsrad Entfernen Sie die Verschmutzung Strom wird nicht richtig zugeführt Überprüfen Sie die Stromzufuhr GERÄT LÄUFT NICHT Transformator läuft nicht Überprüfen Sie den Transformatoranschluss...
  • Seite 30 Teilenummer Beschreibung NC1001 NC31 & 32 Gehäuse NC1022 Gehäuse des Wandaufsteigers NC1009 NC31 & 32 Pumpenmotor NC1024 Pumpenmotor des Wandaufsteigers (Version 1) NC1024:02 Pumpenmotor des Wandaufsteigers (Version 2) NC1013 NC31 & 32 Netzteil NC1023 Netzteil des Wandaufsteigers NC1012 NC31 & 32 Schwebekabel NC1012XL Schwebekabel des Wandaufsteigers NC1012XL:02...
  • Seite 31 Diese Garantie gilt für den ersten Verbraucher/Käufer für einen Zeitraum von 12 Monaten ab dem Kaufdatum. Diese Garantie gilt nur für einen normalen und vernünftigen Gebrauch von Nitro. Durch Schäden, Defekte, Störungen oder andere Fehler, die aus dem Gebrauch ohne den ursprünglichen Transformator bzw.
  • Seite 56 www.smartpooleurope.com • info@smartpooleurope.com...

Diese Anleitung auch für:

Nc32eu

Inhaltsverzeichnis