Viking AIR PLUS PRO-RT Gebrauchsanweisung Seite 7

EN
VIKING AIR PLUS PRO-RT - instruc�ons for use
Thank you for choosing a VIKING product. Please refer to the technical specifica�ons of each model in the user manual or on the website
www.best-power.cz
Descrip�on of the device
Indicator light
Instruc�ons for use
Pairing earphones with Android/iOS devices
1. Open the charging case cover, the earphones will turn on automa�cally.
2. Se�ngs>Bluetooth>Turn off (menu may vary depending on device).
3. Select the device named "EP058", if the mobile phone asks for a password, enter four zeros (0000).
4. Once successfully connected, the earphones can be used.
Shutdown
Insert the earphones into the charging case and close the case cover for 5 seconds to turn the earphones off. The earphones can also turn off automa�cally
without the device connected (a�er 3 minutes).
Earphones control
During calls
Incoming call ringtone: The earphones is equipped with a ringtone.
Receiving calls: press the le�/right earphones once to answer a call.
To hang up a call: Press the le�/right earphones once to hang up a call.
Press the le�/right earphones twice to reject the call.
With music
Play/pause: Press the le�/right earphones once to play or pause a song.
Previous track: press the le�/right earphones three �mes for the previous track.
Next track: press the le�/right earphones twice for the next track.
Volume up: swipe up on the le�/right earphones to increase the volume.
Volume down: swipe down on the le�/right earphones to lower the volume.
Voice control via Siri
Siri can be customised on iPhone in Bluetooth se�ngs. Long press the headphones for 1.5 seconds to turn Siri on.
Switching between the two earphones
The earphones can be freely connected to the mobile phone (only one earphone or both), and once triggered, they connect within seconds. You can wear
one or both earphones and switch seamlessly between them.
Enable/disable noise reduc�on mode, transparency mode
Long press the le�/right earphone bu�on for 2 seconds to switch between the three modes (noise cancella�on, transparency and mute). The mute mode
must be set to - Aplus - noise cancella�on - check/uncheck on iOS.
Edit earphone name in bluetooth
On your mobile phone in the bluetooth se�ngs, you can edit the name of the earphones.
GPS loca�on of earphones
The earphones can be located via the search app (Find My), once located the earphones should appear on the map. The search app (Find My) must be
downloaded (works only for iOS).
Sensor in earphones - TWS
A�er successful pairing of the TWS, a "dong" tone is heard on the first earphone and no tone is heard on the second earphone. The term TWS, or True
Wireless Stereo, refers to a technology that allows two audio devices to be paired via Bluetooth.
Restore earphones to factory se�ngs
Long press the charging case bu�on for 8 seconds and release it when the light indicator starts flashing orange.
Earphone status descrip�on
A "dong" tone sounds when the sensor is connected, disconnected, switched on, or in noise cancella�on mode.
A "beep" "beep" tone sounds when the ba�ery level of the earphones is low.
Audible "beep" tone when touched.
Charging the charging case
1. Connect the lightning cable to the charging case input.
2. Connect the cable to a power source (adapter).
3. While the charging case is charging, the light indicator turns orange. The charging case will be charged in about 1.5h or more.
Charging case states (sound and light indicators)
When charging or opening the cover of the charging case that is a�ached to the mobile phone, a ringing tone sounds. No ringing tone will sound when the
mobile phone is not connected.
When connected to a mobile phone, pressing the bu�on (also valid for a long press of 15 seconds) on the charging case always sounds a ringing tone.
Touch area
Charging port
Replacement silicone a�achments for headphones:
To replace, press the bo�om of the a�achment
(If it is difficult to pull out, pull them out with a slight �lt.)
Pull out a�er turning.
BONA SPES s.r.o.