ENTAC EPFH2000-B Bedienungsanleitung

EPFH2000 B
USER INSTRUCTIONS
EN
Read all the instruction carefully before you use the appliance and keep it for future use.
Preparation before operating
1. Check if the electrical voltage of the main supply and the load of the socket match the rated voltage and power marked on the rating label of the appliance.
2. Check if the socket and the plug are undamaged,and put the plug well in the socket.
3. Put the appliance on a stable and flat surface for no risk of falling down.
4. Be sure that there is enough space for the fan heater while operating, at least 50 cm around the appliance, and right before the air outlet, the distance should be at least 120 cm.
Safety Precautions
1.Don't cover the fan heater at any time when operating.
2.Don't hang it on the wall.
3.Don't use it on the carpet with long fluff.
4.Don't use the heater in the immediate surrounding of a bath, a shower or a swimming pool.
5.Don't insert sticks or any other objects to either the air inlet or the outlet of the appliance.
6.Don't put the appliance immediately below a electrical socket.
7.Don't put the appliance near a fire.
8.Keep children away from the heater.
9.Keep flammable and explosive objects away from the heater.
10.In case of malfunction or abnormal operation, don't attempt to open or repair the appliance at home, send the heater to appointed service agent for inspection and repair.
11.If the power cord is damaged, it must be replaced by the appointed service agent or a similarly qualified person.
Operation instructions
Security System
"1.To avoid risk to human being or damage to internal components, the fan heater has a security system which will automatically switch off the appliance if the heat reaches the safety limit. If overheating occurs:
1.1 Turn the heat select switch to "O" position, turn the thermostat switch to the minimal position and remove the plug from the socket.
1.2 Check that nothing is approach the outlet and or inlet. If so, re-position the heater before starting again.
1.3 Let the fan heater cool down for 8 to 10 minutes before you start it again.
1.4 Plug in the appliance and switch it on. If the appliance can't operate normally, remove the plug immediately from the socket and have the fan heater serviced by an appointed service only.
Maintenance and Cleaning
1. Before you turn off the appliance, turn the heat select switch to the "
2. Clean the air inlet and air outlet of the appliance regularly (at least twice a year normally).
3. Before you clean the appliance, turn off the heater first, then remove the plug from the socket, and wait until the appliance cools down.
4. Use a damp cloth to clean the surface of appliance, avoid water going inside the appliance, dry the appliance before use or storage.
Warning
·This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
·Children should be supervised to ensure that they do not play with the appliance.
·If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
·CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off
by the utility.
·The instructions for heaters marked "Do not cover" or with the "Do not cover" symbol shall contain the substance of the following: WARNING: In order to avoid overheating, do not cover the heater.
·The instructions shall state that the heater must not be located immediately below a socket outlet.
·Do not use this heater with a programmer, timer or any other device that switches the heater on automatically, since a fire risk exists if the heater is covered or positioned incorrectly.
·Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool.
EN DE HU RO SK CZ HR SI SR PT LT PL GR IT ES FR BG
" position. After operating for 3 to 5 minutes to lower the internal temperature of appliance, then turn the heat select switch to "O" position.