Miyota FS60 Bedienungsanweisung

Instruction manual
English
Features
This watch is an analog quartz watch equipped with features
including a Day retrogrode display and chronograph function.
Displays and Buttons
Chronograph
second hand
Chronograph
minute hand
Hour hand
Second hand
Setting the Time
hand
correction
Swoud band
Setting the Date
Date arrection
* The date is based on a 31-day calendar. The date must be changed from
the last day of the month to the first day of the following
months not having 31 days (months having 30 days and February).
* The date will change in 10:00 PM - 12:00 AM.
3. Once the date has finished being set, return the crown to the
normal position.
Setting the Day
DaE
Cal.FS60
Minute hand
Button(A)
Day band
1. Pull the crown out to the time
correction position when the
second hand has reached the O
seconds position.
2. Turn the crown to set the time.
3. Securely return the crown to the
normal position in
synchronization with a telephone
or other time service.
1. Pull the crown out to the date
correction position.
2. Turn the crown clockwise to set
the date.
* If the date is set while the time on
the watch is between the hours of
about 9:00 PM and 1 AM, the
date may not change on the
following date. If this happens, set
the date after temporarily moving
the hands to a time other than
between the above times.
month for those
1. Pull the crown out to the date
correction position.
2. Turn the crown anti-
clockwise to set the date.
* If the day is set while the time
on the watch is between the
hours Of about 11 PM and
2:00 AM. the day may not
change on the following day.
• The day will change in 1:00
AM - 2:00 AM.
3. Once the day has finished
being set, return the crown to
the normal position.
Using the Chronograph
minute hand
Button(B)
[Chronograph Timing)
1. Start timing by pressing button (A).
* The chronographis repeatedly startedand stoppedby pressingbutton (A).
2. Pressingbutton (B) resetsthe chronograph to Oseconds.
Time
Measurement
Zero Positioning of Chronograph
(After Replacing the Battery)
minute hand
[Chronograph Hand Zero Positioning]
1. Pull the crown out to the time correction position.
Press button (A) to position the chronograph second at the Oposition.
* The chronograph second hand can be advanced rapidly by depressing
button (A) continuously.
3. Once the chronograph second hand has been positioned at the O
position, reset the time and return the crown to the normal position.
4. Press button (B) to check that each of the chronograph hands has
been reset to the O position.
Specifications
1. Caliber. No: FS60
2. Type: Analog quartz watch
3. Timekeeping accuracy: Within ± 20 secondsper month on
average (when worn at normal
temperatures of +50C to +350C / 41 OFto
950F)
4. Crystal oscillator: 32,768 Hz
S. Operating temperature range: -IOOCto +600C/140F to 1400F
6. Display functions:
• Time: hours, minutes. seconds
* Calendar: Day, Date
* Chronograph: Measurementand display up to 59 minutes 59 seconds
in 1 second units
7. Battery: Miniature silver battery, 1
Battery part no.: SR626SW
Battery life: Approx. 2 years (when using the chronograph for
1 hour/day)
* Specifications are subject to changewithout notice.
m IYOTA
Ihe chronograph function of this
watch is able to measureand display
elapsed time up to 59 minutes 59
seconds in I second units. After
chronograph displays elapsed time
for 59 minutes 59 seconds, it
resumes timing from O seconds. The
chronograph minute hand continues
to move until the chronograph is
stopped by pressing button (A) even
after 59 minutes 59 seconds have
elapsed.
Stop
(A)
(B)
(B)
Hands
When resetting the
chronograph after replacing
the battery, if the chronograph
second hand does not return to
the O seconds position or if the
chronograph second hand has
shifted out of position due to a
strong impact, perform zero
positioning of the chronograph
hands according to the
procedure described below.
the