2 Sicherheitshinweise akku) muss aus Sicherheitsgründen immer zusätzlich ein geladener, ausreichend großer Empfängerakku verbaut werden (siehe BEC Der KOSMIK ist ein Produkt, das aus- 4.3). Fehlfunktionen, z.B. durch Kabelbruch, schließlich für den Modellbaubetrieb vor- Kurzschluss, Wackelkontakt oder Ausfall eines gesehen ist. Keinesfalls darf der KOSMIK in BEC-Bauteils, führen sonst zum Ausfall der bemannten Anwendungen eingesetzt wer- gesamten Empfangsanlage.
Akkuspannung zu kompensieren. solange bei Vollgas d der zulässige Dauerstrom nicht überschritten wir ird. • Abschaltanalyse: der Abschaltgrund wird der Abschaltgrund wird 3.4 Tiefentladungsschutz durch Blinkcode angezeigt. Ist eine SD ngezeigt. Ist eine SD-Card Die KOSMIK Regler sind mit einem Tiefent Die KOSMIK Regler sind mit einem Tiefent- gesteckt, wird automatisch ein durch matisch ein durchgehen-...
ACHTUNG: Vorab bitte die Vorab bitte die entsprechende Spezifikationen der Akkus, der Servos und Spezifikationen der Akkus, der Servos und Empfänger auf Kompatibilität zur jeweils Empfänger auf Kompatibilität zur jeweils gewünschten Spannung prüfen gewünschten Spannung prüfen ! Betrieb ohne BEC: Beim Beim Betrieb...
und bringt den Rotor schneller auf Drehzahl. r schneller auf Drehzahl. Im KOSMIK sind folgende Schutzm mechanismen aktiviert: Dadurch sind abrupte Abfangmanöver Abfangmanöver möglich. • Wird Wird länger länger Sek. Sek. kein kein gültiges Die Hochlaufzeit ist dabei von der zu ie Hochlaufzeit ist dabei von der zu beschleu- Empfangssignal erkannt, schaltet der Regler Empfangssignal erkannt, schaltet der Regler...
5.2 Motor-Kabel KOSMIK können leistungsstarke Der Anschluss der 3 Motorkabel ist beliebig. Das Digitalservos folgender Spezifikation Tauschen von 2 Motorkabeln ändert die Motor- betrieben werden: drehrichtung. Alternativ kann Motor- KOSMIK 160 Dauerstrom drehrichtung über PROGDISC geändert werden. kurzzeitiger Maximalstrom Sollte der verwendete Motor über Sensor- KOSMIK 200 10A Dauerstrom leitungen verfügen, so werden diese nicht...
7. Programmierung 3.1 beschrieben). Gasknüppel auf Stellung „Motor-Aus“ (0%) stellen. 7.1 Modus 1 - APM (Reset) Den KOSMIK mit dem Empfänger (BEC- Kabel) Die Programmierung mit Modus 1 löscht alle verbinden. Das Kabel für den Gaskanal nur in vorher getätigten Einstellungen. die mit „Master“...
stecken. Empfänger einschalten. einem 10S Akku zu programmieren und dann die u zu programmieren und dann die Motorkabel mit dem Motor verbin nden. gleiche Drehzahl hzahl einem einem Akku Antriebsakku an KOSMIK anschlie eßen. verwenden. Modus LED (LED 1) blinkt grün. Es Es erklingt ein Bei Änderungen am Set Setup (Motor, Übersetzung,...
Achtung: Nach abgebrochener Nach abgebrochener Autorotation Position 1: 0% = Motor- Aus Position 2: 100% = Vollgas ergeben sich durch das schnelle Hochfahren ergeben sich durch das schnelle Hochfahren hohe hohe Belastungen Belastungen für für Mechanik. Überprüfen Sie im Senders, ob die berprüfen Sie im Senders, ob die Werte auch angefahren werden (siehe auch ab 3.1 auch ab 3.1).
die PROGDISC in der Bildschirmausgabe die mit „Master“ gekennzeichnete Buchse stecken. Empfänger einschalten. der Update- Software ausgegeben. Motorkabel mit dem Motor verbinden. Sobald der PC die PROGDISC und die Antriebsakku an KOSMIK anschließen. PROGDISC den KOSMIK erkannt hat, kann Modus LED (LED 1) blinkt grün. Es erklingt ein die Schaltfläche Update angewählt werden.
10 Fehlerbehebung 11.1 Recycling Elektronische Bauteile dürfen nicht Grundsätzlich: Hausmüll geraten, sondern müssen nach Der KOSMIK zeigt mittels seiner LEDs mögliche Gebrauch sach- und umweltgerecht entsorgt Diagnosezustände an. werden! Die nationalen und regionalen Abfallbestim- Problem LED1 LED2 mungen müssen befolgt werden. Elektronische Motor aus nicht erkannt Blinkt grün Blinkt grün Abfälle sind den dafür vorgesehenen Systemen...
12 Technische Daten Technische Daten KOSMIK Default einstellbar (PROGDISC) Anschlüsse: 1 x USB, 1 x MicroSD, 2 x Fernsteuerkabel, 3 x Sensoranschlüsse, 2 x Akkulaschen, 3 x Motoranschlusslaschen BEC Spannung 5,6 V 5 – 8 V BEC-Dauerstrom KOSMIK 160+HV 7,0 A BEC-Dauerstrom KOSMIK 200+HV 10,0 A BEC-Maximalstrom (kurzzeitig) KOSMIK 160+HV...
Seite 14
1 Definitions Contents Auto-Programming-Mode Definitions electromotive force Delivery content Autorotation/Bail-out Battery Eliminating Circuit to power the Safety instructions receiver from the main battery) Basics KOSMIK KOSMIK ESC Preparing the handheld transmitter Button control knob for mode programming Preparing the mode Active light / control Smooth start Mode...
capacity in addition (also see BEC 4.3). 2 Safety instructions Malfunctions, e.g. by cable break, short circuit, slack joint or failure of a BEC-component, KOSMIK is a product that is designed leads to loss of the entire receiver system. exclusively model-flight operation.
KONTRONIK recommends for optimum KONTRONIK recommends for optimum governor If you have any question about use, If you have any question about use, operating or control a value of about 80% in the transmitter in the transmitter programming of the ESC, please programming of the ESC, please contact our (equivalent to100% is the full throttle 100% is the full throttle way).
4.2 Cooling and mounting Never remove the torodial core from the core from the cable! Sufficient cooling increases efficiency Sufficient cooling increases efficiency and life- It can be moved within the cable to any can be moved within the cable to any position, but take care for tight fit of the but take care for tight fit of the cables afterwards span of the ESC.
5 Connecting the ca ables 4.10 Helicopter mode WARNING: always use always use only the included In helicopter mode the RPM control is In helicopter mode the RPM control is active. The cable assemblies assemblies (motor battery motor RPM speed is kept constant. cables).
5.2 Motor cables 6. Getting started Connecting the 3 yellow motor cables is at your Always use polarized connectors for wish. Exchanging two of the cables changes battery cables only! Connecting the battery the direction of motor rotation. Alternatively, the with reverse polarity will destroy the ESC ! direction of motor rotation can be changed via PROGDISC.
7. Mode programming Connect the cable to the receiver’s jack (that is designated for throttle function) and the other 7.1 Mode 1- APM (Reset) side into the KOSMIK’s jack, that is marked as When programming the APM mode, all previously Master.
designated for throttle function) and the other stored side into the KOSMIK’s jack, that is marked as In mode 4 the ESC reads all parameters (such as Master. Then switch on the receiver. the ratio between selected RPM in the transmitter Connect the motor cables to the motor.
Position 2 = 100%! Programming mode 4: For AR mode use there is in addition to 100 For AR mode use there is in addition to 100% (full throttle) and 0% (motor off) position a third, the position a third, the AR-on-position necessary.
KOSMIK is automatically detecting the throttle Plug the PROGDISC to a Windows ™ PC and connect to the Internet. position. Start the download from the KONTRONIK homepage (www.kontronik.com) of the current Programming mode 6: software version for your KOSMIK by saving the Switch on and prepare the transmitter (as file to your PC.
10 Troubleshooting 11.1 Recycling Basically: Electronic components must not be disposed with household waste but have to be disposed according to legal and environmental regulations. The KOSMIK shows by the light of the LEDs the have to be possible problems. National and local disposal regulation respected! Problem...
12 Technical specification Technical specifications KOSMIK Default adjustable (PROGDISC) Connections: 1 x USB, 1 x MicroSD, 2 x BEC cable, 3 x Sensor cable, 2 x battery brackets, 3 x motor brackets BEC voltage 5.6 V 5 – 8 V BEC peramnent current KOSMIK 160+HV 7.0 A BEC peramnent current KOSMIK 200+HV...
12.1 Kabelverlegung am KOSMIK am KOSMIK / Routing cables on the KOSMIK E M5 x 10 M5 x 10 mm d = 5,3 d = 5,3 mm d = 5,3 mm Schrumpfschlauch heat shrink tubing...
Seite 27
13. Meldungen, ihr Abschaltverhalten und ihre Konsequenzen Messages, shut down behavior and consequences. Motorflug /Boot Fehlertyp / Segelflug/ Sports plane Helikopter / Grund / Reason Type of Error glider / boat helicopter RC-Car Meldungen im Betrieb / messages in Akku Unterspannung / Abschaltung Abschaltung Abregelung...
Seite 28
Regler defekt / ESC defect 34 Error Bitte Einschicken / please send in for repair Bitte Akku prüfen / please control the battery Unterspannung 35 Error Bitte Akku prüfen / please control the battery Überspannung 36 Error S_BEC Unterspannung 37 Error BEC / Pufferakku prüfen / please control the buffer pack S_BEC Überspannung 38 Error...