Werbung
Verfügbare Sprachen
Verfügbare Sprachen
PREDATOR
228
Overview
Fire
button
Bottom
cover
lock
button
This will switch the screen display on and Off
3. Key lock function:
While the device is on, simultaneously press the two regulatory buttons. This will switch
between Key Lock and Key Unlock function
4. Micro USB Port function:
The USB port can be used for charging and upgrading firmware It is better to
take out the cells and charge them through external charger
5. Switch
the display mode: By pressing the eft and right regulatory buttons simultaneously
state, the screen display will rotate 180 degrees. You can then view the screen from two kinds Of angle
through this operation.
STEALTH
STEALTH
2)
Shift among VWITC-Ni/TC-Ti/TC-SS/TCR
Mode
Press the fire button 3 times to enter into the mode options. Then press the right regulatory button to switch
English
3
(4). Keep pressing the fire button or leave the interface for about 10 seconds to confirm
Following
is the TCR value range for your reference:
Material
Nickel
NiFe
Titanium
ss (303, 304, 316, 317)
Note: 1 The TCR value in the sheet is 105 multiplied of the actual TCR
2 The TCR value range is 1-1000
Supplementary
TC Modes Functions:
Temperature
adjustment:
In TC modes, the temperature can be adjusted from (100-3150C or 200-600'F)
with the two regulatory buttons, right to increase and left to decrease.
Shift between oc and •F: f you increase the temperature to 3150C, and continue to press the right regulatory
button, the temperature readings will automatically change to the owest Fahrenheit (2000F). Equally, if the
temperature is decreased below the minimum (1000C), the unit WII change back to •F automatically, and the
temperature will start to decrease from 600'F.
Wattage adjustment:
While the wattage sign blink, press the right or left regulatory button to adjust the wattage,
5
then you enter into the Logo Mode. Press the left regulatory button to choose between logo "ON"
and "OFF", and press the fire button to confirm
You can download our logo. You can also make logos to your preference, and then import it through
software The logo should be monochrome image in the format of bmp with limited 64848 pixel
The setting
Of Preheat Function:
(1). Long press the fire button and right regu atory button simultaneously to enter the menu
(2). Press the right regulatory button to enter the preheat setting menu
(3). Press the fire button to switch between preheat power and preheat duration.
(4). Press the left or right regulatory button to decrease or increase the parameter.
(5). Long press the fire button to confirm
USB Charge Function:
1. Function
of charging
mobile phone: Connect the RC adapter with mobile phone through USB
cable. When the device is on, press the fire button once to start charging
2. Function
of charging
other electronic
devices:
(1). While the device is on, keep pressing the fire button and right regulatory
button simultaneously,
and then you enter into the sub menu.
(2). Press the right regulatory button two times to enter into the USB
CHARGE
(3). Make sure the USB CHARGE is on
(4). Press the flre button three times to switch to USB charging mode
English
7
Weak Battery Alert:
In VW/TC mode, when the device installed with an atomizer is working and the voltage
of battery is below 2 9V, the device shows "WEAK BATTERY'
power will be reduced accordingly.
Low
Power
Alert:
If the power of battery is lower than 10%, the power symbo on the screen will flash.
Imbalanced
Alert:
When the difference between the maximum and minimum cell voltage is equal or greater than 0 3V
Screen will display " MBALANCED BATTERIES" after inserting the USB cable. Then please take out the cells
to charge or replace with freshly charged cells
Check USB Alert: When the vo tage Ofthe USB charger is equal Or greater than 5 8V, the OLED screen WII
display "CHECK USB ADAPTER" after inserting the USB cable or vaping
Charge Error Alert: When no current is detected in charging state,
the OLED screen wil display "CHARGE ERROR"
Check Battery Alert: When one of the cells is not insta led correctly,
the OLED screen wil display "CHECK BATTERY"
English
9
510 spring connector
OLED
screen
Regulatory button
Micro USB port
TEHP
HI
HSO
croo
2000
oss
oooe
ooo
LOCK
UHLOCK
TCR Value Range
600-700
300-400
300-400
80-200
FFEHEHI
TIME
use
DETECTING
LT
PE78HR
FORER
Meanwhile, the output
1 OH
aa
0002
HERK
ERTTERV
CHECK
CHARGE
ERROR
Specification
& Features
Weight: 166 2g
Size: 43
Thread Type: 510 spring loaded thread
Cell type: High-rate 18650 cell (discharge current should be above 25A)
output Mode: VWITC-Ni/TC-Ti/TC-SS/TCR
Output Wattage: 1-228W
Resistance Range: 0 05-1 50hm for TC modes
0 1-3 50hm for VW mode
Temperature
Range: 100-3150C/200-6000F
Maximum Charging Current: 2A
Maximum Output Current: 50A
Output Voltage Range: 0 5-9V
How
to use:
1. Power on/off: Unlock the bottom cover button and put two 18650 cells into the battery body. Press the fire
button 5 times in quick succession to turn the device on and off.
(Note: Please adjust the wattage to a proper range to match the atomizer you used before using Moreover,
please be careful not to use battery with torn shell for safety.)
2. Stealth function:
While the device is on, simultaneously hold the fire button and the left regulatory button
between VW/TC (Ni, Ti, SS)/TCR (MI, M2, M3) mode.
Press
the fire
button
to conflrm
Under TC/TCR mode, while the mode sign flashing,
press the left regulatory button to enter into its
submenu. Then press the right regulatory button to
choose TC-Ni/Ti/SS
(TC mode) or MI/M2/M3(TCR
mode). Press the fire button to confirm
in shutdown
VW
Mode:
In this mode, output wattage can be adjusted from IW to 228W by pressing
the regulatory buttons, right to increase and left to decrease.
TC-SS
Mode:
The TC-SS
TCR (MI, M2, M3): In TCR (Temperature Coefficient of Resistance) mode,
users can set the parameters according to the TCR Of coil
The Setting of TCR Mode: In powered-off state, keep pressing the fire button and right regulatory button
simultaneously, then you enter into the TCR set menu:
5)
(1). Press the left or right regulatory button to choose among T CR MI, M2 and M3;
(2). Press the fire button to confirm the mode you chosen;
(3). Press the left or right regulatory button to increase or decrease the parameter according to the TCR Of coil;
and press fire button to confirm Long pressing the right or left regulatory button will make
TCR
SET
the wattage setting rapidly increase or decrease
Resistance
locked function:
button to lock or unlock the resistance of the atomizer. (Note: Such operation should be
carried out at room temperature.)
New atomizer
installation:
coo ed to room temperature. If a new atomizer has not coo ed down before attaching,
the temperature may read and protect incorrectly until the new atomizer cools
Note: 1 .When you connect a new atomizer or disconnect and reconnect your existing atomizer, the device will
prompt you to confirm this change and a message will prompt "NEW COIL RIGHT, SAME COIL LEFT". Press
the right regulatory button to confirm that a new atomizer has been attached. Press the left regulatory button to
confirm
that
the
same
2 When using normal coil or the resistance of coil you used is higher than 1 50hm in
TC modes, the device will automatically switch to VW mode
Shift between Puff and Time: While the user information sign blink, press the right
regulatory button to shift between Puff and Time
Logo Mode:
When powered on, press the fire button and right regulatory button simultaneously
(5). When it is fully charged, the OLED screen wil display USB CHARGE STOP.
OFF
Malfunction
Indication
No Atomizer
Alert: When the device does not detect an atomizer, the OLED screen wil display
"NO
ATOMIZER
FOUND"
Atomizer
Low
Alert:
When
a.o
s
than 0 050hm in TC modes, the OLED screen will display "ATOMIZER LOW'
Atomizer
Short-circuit
OLED Screen will display "ATOMIZER SHORT"
Temperature
Alert:
If the internal temperature of the device is over 700C, the output will shut off
automatically and the screen will display "DEVICE TOO HOT"
Over
10 Second
Protection:
When the power button is pressed for over 10 seconds, the output will shut Off
and the OLED screen will display "OVER IOS PROTECT"
s.0U
OLT
s.0U
MP 678
HR
Temperature
Protection:
reaches the set temperature, the device shows "TEMP PROTECT"
Warranty
Please consult with your WISMEC distributors for warranty policy We are not responsible for any damage
caused by user error.
This warranty is only valid for authentic WISMEC products within warranty period from date of purchase by
0.22
the
end
user
21
z
Warning
1 Keep out of reach of children
2 This product is not recommended for use by young people, non-smokers, pregnant or breast-feeding
women, persons who are allergic/sensitive
, the OLED
Contra-indication
1 Only have your product repaired by Wismec
personal Injury may occur
2 DO not leave the product in high temperature or damp conditions, as this may damage the product. The
appropriate operation temperature is within OOCto 450C while charging and -IOQC to 60QC while in use
3 Keep away from water
Possible
adverse
effects
1 Use of this product may cause damage to health
CHECK
2 For people with adverse reaction after using this product, it is recommended to use the juice with lower
ERTIERV
nicotine
content
or no nicotine.
7 mm
Mode
(TC modes)
7.24
aaa.0
oooa
ooo
0002
mode is suitable
to SS316
coil
While the resistance sign blink, press the right regulatory
In TC mode,
be careful
to attach
new atomizers
atomizer
has
been
reconnected
and Protection:
the
resistance
of atomizer
is lower
than
O. 1 ohm
Protection:
When atomizer
short-circuit
occurs,
In TC modes, if the actual temperature Of coil
to nicotine.
Do not attempt to repair the unit by yourse f as damage or
2
TEHP
u
IEHP
SS
ICR
I eo
Hi
eas
o_aa
aaao
o_ea
aes_o
ooaa
00.0
0002
ooo
oooa
ooo
TOR 120
ICR
120
tte
ICR
120
aooe
00.0
0002
00.0
0002
ooo
4
TEHP
HI
HSO
HE"
COIL
o,asn
RIGHT
0002
00.0
COIL
aeon
that have
TEHP
HI
HE.O
HSO
0002
ooo
oaoa
00.0
and
6
CHARGE
srop
in VW
mode
or
ower
the
nmoHIZER
RTOHIZER
AT üHIZER
SHORT
FouH0
PROTECT
aaec
oes
oooa
ooo
OEUICE
OVER
IOS
HOT
PROTECT
English
8
10
Werbung
