Inhaltszusammenfassung für Hazet-Werk 9040N-10-01/3
Seite 1
H A Z E T- W E R K HÖCHSTE TECHNOLOGIE IN DER WERKZEUGFERTIGUNG SEIT 1868 HIGHEST TECHNOLOGY IN TOOL MANUFACTURE SINCE 1868 9040N-10-01/3 9040N-13-01/3 Reparaturanleitung Aufrollführung Schlauchaufroller Druckluft Roll-up Guide Repair Instructions Air Hose Reel...
Seite 2
1965-20 Ursprungssprache deutsch – Original language German HAZET-WERK Hermann Zerver GmbH & Co. KG ; Güldenwerther Bahnhofstraße 25 - 29 · 42857 Remscheid · GERMANY } 10 04 61 · 42804 Remscheid · GERMANY · [ +49 (0) 21 91 / 7 92-0 \ +49 (0) 21 91 / 7 92-375 (National) ·...
Seite 3
Entfernen der seitlichen Abdeckung. Die 4 mit Pfeilen markierten Schrauben demontieren.
Seite 4
Die Abdeckung mit Hilfe des Keils aufspreizen und den Keil zur Fixierung stecken lassen. Haltestift der Aufrollführung entfernen.
Seite 5
Demontage der Aufrollführung. Zur Fixierung des Zahnriemens, kann der zuvor demontierte Haltestift verwendet werden. Im Anschluss erfolgt die Demontage der Aufrollführung.
Seite 6
Demontage der beiden Schrauben in der Aufrollführung. Demontage der beiden Stifte in der Aufrollführung.
Seite 7
Montage der neuen Aufrollführung. Zuerst die Schrauben und die Stifte demontieren, dann den Mechanismus um den Schlauch bauen. Einsetzen der beiden Stifte in der Aufrollführung.
Seite 8
Montage der beiden Schrauben in der Aufrollführung. Aufsetzen des Zahnriemens auf das Zahnrad.
Seite 9
Einsetzen der Schlauchführung. Die Position auf der Gewindewalze muss ganz rechts sein, wenn der Schlauch fast komplett aufgerollt ist. ACHTUNG: Die richtige Führung des Zahnriemens beachten.
Seite 10
Entfernen des Keils. Gehäuse mit Schrauben schließen.
Seite 11
1965-20 Original language German HAZET-WERK Hermann Zerver GmbH & Co. KG ; Güldenwerther Bahnhofstraße 25 - 29 · 42857 Remscheid · GERMANY } 10 04 61 · 42804 Remscheid · GERMANY · [ +49 (0) 21 91 / 7 92-0 \ +49 (0) 21 91 / 7 92-375 (National) ·...
Seite 12
Remove the side cover. Remove the 4 screws marked with arrows.
Seite 13
Spread the cover using the wedge and leave the wedge in place to fix it. Remove the retaining pin of the roll-up guide.
Seite 14
Removal of the roll-up guide. The previously dismantled retaining pin can be used to fix the toothed belt. The roll-up guide is then removed.
Seite 15
Removal of both screws in the roll-up guide. Removal of both pins in the roll-up guide.
Seite 16
Installation of the roll-up guide. First remove the screws and the pins, then build the mechanism around the hose. Insertion of both pins in the roll-up guide.
Seite 17
Installation of both screws in the roll-up guide. Mounting the toothed belt on the sprocket.
Seite 18
Inserting the hose guide. The position on the thread roller must be all the way to the right when the hose is almost completely rolled up. ATTENTION: Observe the correct guidance of the toothed belt.
Seite 19
Removal of the wedge. Close the housing with screws.