avidsen TEHA 320 Bedienungsanleitung Seite 2

TEHA 320
EN
MOTOR DRIVE KIT
V1
With actuators – For two-panel swing gates
Ref. 114300
COMPATIBLE WITH ALL SOLAR OPTION OPTION SMARTPHONE
TYPES OF OPENWORK BACKUP BATTERY COMPATIBILITY
GATES OPTION
Thank you for purchasing an automatic gate opener.
This document is a quick start guide detailing the main installation steps as well as the equipment required. To install,
please download the installation manual at the following address: http://www.avidsen.com
Warning: The safety instructions and installation instructions can be found in the installation manual. Follow all these instructions, as an
incorrect installation can cause serious injuries.
CONTENTS OF THE KIT
1
x 1
5
x 2
1 Actuators 5 Gate mounting bracket
2 Switchgear 6 Post mounting bracket
3 Flashing light
4 Remote control
EQUIPMENT REQUIRED (NOT SUPPLIED)
The tools and screws required for the installation must be in good condition and compliant with applicable safety standards.
actuators attachment to the
fl ashing light
post:
- electronic panel
3m cable
10m cable
2 x 0.5mm2
2 x 1.5mm2
2 3
x 1 x 1
6
x 2
drilling the
post
drilling into
the gate
attachment of the
attachment of the
fi xing the brackets to the
brackets
fl ashing light onto the
gate:
onto the posts:
Choose a screw/nut
system adapted to the
thickness of the gate.
There are 4 fi xing points
INSTALLATION
Safety guidelines: please refer to the installation manual for all safety instructions.
To perform the installation, please download the installation manual at the following address: http://www.avidsen.com
Overview:
The cables used must be appropriate for outdoor use (such as H07RN-F for example).
The cable run between the two posts must comply with applicable standards (NFC 15-100).
The geared motor power cable must run 80cm deep with red warning mesh.
Switchgear
control unit
1
List of cables:
1 230VAC power line
2
4
x 2
3
4
The installation is a 4-step process:
1. Installation of the actuators onto the posts and gate, and of the electronic panel.
2. Electrical connection of the motors and electronic panel to the mains. This connection must be performed by qualifi ed personnel
(electrician, etc.).
3. Adjustments and operation:
Warning: Only switch on the electronic panel once all connections have been made.
- Read the installation manual chapter on simple adjustments.
- Launch the movement self-learning programme (press "+" for 3 seconds)
- Programme the remote controls:
- press "-" for 3 seconds
- press "OK"
- press the remote control button to be memorised
- Repeat the operation for each remote control
- Choice of operating mode:
By default, automatic closing is deactivated. To activate it, you must install a pair of photocells
4. Operational testing: To familiarise yourself with the automatism and ensure it operates properly, read the chapter on usage and conduct operational tests (open/close, initiate
obstacle detection, cut the photocell beam). Upon completion of these tests, you may have to modify certain settings (e.g. motor power).
EU DECLARATION OF CONFORMITY
Avidsen declares that the equipment complies with the essential applicable requirements of RED Directive 2014/53/EU.
Directive 2014/35/EU: (protection of users' health and safety)
Directive 2014/30/EU: (protection requirements relating to electromagnetic compatibility).
Directive 2014/53/EU: (effi cient use of the radio spectrum, in order to avoid harmful interference).
The full declaration of compliance is available on the website www.avidsen.com
post
IN Tours, 23/09/2023
Alexandre Chaverot, CEO
fl ashing light
actuators
4
2
Inner side of the property
Connection Cable
Cable 3 x 2.5mm2 (more than 30m long)
Cable 3 x 1.5mm2 (less than 30m long)
Left motor Cable 2 x 1.5mm²
Right motor Cable 2 x 1.5mm²
Flashing light Cable 2 x 0.5mm²
19 avenue Marcel Dassault - ZAC des Deux Lions - 37200 Tours - France
3
Max length
Unlimited
10m
10m
3m
Pour en savoir plus :
www.quefairedemesdechets.fr
Avidsen