Seite 2
ORIGINAL OWNER of each product (provided it was swimming pool, wet basement, etc. PLACE OF INSTALLATION: purchased at an authorized NOVA Dealer) that it is free • Read all of these instructions clearly! • The unit should be used only on a clean, horizontal of defects in materials and workmanship and that each •...
Seite 3
Gerätezustand und nur mit dem original vom Hersteller bzw. stillschweigenden Gewährleistungsregelungen beigelegtem bzw. empfohlenem Netzkabel. entstanden sind. Falls ein NOVA Produkt Service • Es dürfen nur Sicherungen vom Typ IEC 127 und der benötigt, sollte der Eigentümer des Gerätes ein angegebenen Nennstromstärke verwendet werden.
1. Connection Panel & Features Anschlüsse & Features Connection Panel Anschluss-/ Bedienfeld LCD display LCD Display Graphical LCD display showing all paramters of the Grafisches LCD Display zur Anzeige aller Parameter des internal EASY CONTROL DSP . integrierten EASY CONTROL DSPs. INPUT GAIN A Regler INPUT GAIN A Controller Adjusts the level of the input A (input gain).
Seite 5
Whether as stage monitor, fullrange speaker, frontll for larger stages or as hervorragender Klangqualität und zuverlässig hoher Leistung. Ob als delay speaker: The KD12 is the ideal allround solution for the up-market user. Bühnenmonitor, Fullrange-Lautsprecher, Frontll auf größeren Bühnen oder Delay-Lautsprecher: Der KD12 ist eine ideale Allround-Lösung für den...
Connect the speaker only with the original power stimmt (Toleranz +/- 10% zulässig). Schalten mains cable to the wall socket before switching Sie Ihren KD12 Lautsprecher erst ein, wenn on the system. Disconnect the KD12 speaker Sie das Stromkabel mit dem Stromnetz und dem from the wall socket / mains supply, if the system Lautsprecher verbunden haben.
Seite 7
Modus am Eingang gewählt ist (MIC / LINE). Stellen Sie alle Gain Regler in die linke Position bis Anschlag. DIGITAL SIGNAL PROCESSOR Switch ON the KD12 speaker and the NOVA logo Nach dem Einschalten (ON) des Lautsprechers erscheint will be displayed for some seconds (initializing).
Seite 9
CONTRAST: Setting contrast of display Einstellung des Display-Kontrasts LOAD PRESET Scroll to CONTRAST and press the encoder STORE PRESET Scrollen Sie zum Menüpunkt CONTRAST und drücken to enter the menu. Sie auf den DSP-Controller. CONTRAST: Use the encoder to change the setting. Durch Drehen des Encoders kann der Kontrast verändert LOAD PRESET The contrast is adjustable from 0 up to 10.
Seite 10
EXIT Scrollen Sie zum Menüpunkt INFO und drücken to enter the info page. Sie auf den Encoder. KD12 The info page displays the DSP version Die Infoseite zeigt die DSP Version an. Drücken Sie auf FIRMWARE V1.2.0 for your reference. Press the encoder to exit.
Seite 11
4. Setup Applications Anwendungsbeispiele LINE LINE MONITOR APPLICATION WITH MIXER / MONITOR ANWENDUNG MIT MIXER LINE PLAYER & MICROPHONE APPLICATION / PLAYER & MIKROFON ANWENDUNG...
Seite 12
4. Setup Applications Anwendungsbeispiele LINE LINE LOW EQ: PRESETS: FULLRANGE LOW CUT: 120HZ 120HZ LOW-CUT FILTER APPLICATION WITH MIXER AND ONE SUBWOOFER ANWENDUNG MIT MIXER UND EINEM SUBWOOFER...
Seite 13
LINE LINE LOW EQ: PRESETS: FULLRANGE LOW CUT: 120HZ 120HZ LOW-CUT FILTER APPLICATION WITH MIXER AND TWO SUBWOOFERS ANWENDUNG MIT MIXER UND ZWEI SUBWOOFERN...
Seite 14
Power Rating (Continuous / Program): 350 W / 1.000 W 127 dB SPL peak Maximum SPL: LF Driver 1 x 12“/1" NOVA KCB12 coaxial transducer Enclosure: 15mm, birch plywood Suspension / Mounting: 35 mm pole socket, monitor angle 32° Transport:...