SW-Stahl S3229 Bedienungsanleitung Seite 4

S3229 / S3238 / S3239 / S3230
3.15 Stay alert! Watch what you are doing. Use common sense, even unsafe situation or unbalanced
positions, particularly when you are tired.
3.16 This air ratchet wrench comply with the relevant safety regulations. Repairs should only be carried out by an
authorized service facility using original spare parts. Otherwise this may result in considerable danger to the user.
Warning risk of injury
Do not use air tools in potentially explosive atmospheres such as in the presence of flammable liquids, cleaning solvents or
gases. Poor quality or damaged tools such as sockets can fly apart during operation, propelling particles throughout the work
area. Keep hands away from moving parts such as nut runner socket and running tools. Uncontrolled movement of air hose
may occur when it break up or loosen. Unexpected direction of inserted tool movement can cause a hazardous situation. The
tool or inserted tool such as socket may crush by natural worn material and the workpiece. Never wear loose fitting clothes,
or apparel which contains loose straps or ties, etc. which being caught in the rotating spindle of the air tools.
4. Putting into operation
4.1 Air supply and connections. Only use filtered, lubricated, and regulated compressed air. This will increase the efficiency
and useful life of the tool.
4.2 Before connecting the air hose, apply 4 to 5 drops of SAE#10-20 spindle oil at the air inlet. Also, every 3 to 4 hours
of operation, oiling is necessary. Twist Teflon thread tape to ensure a proper seal air inlet. Then tighten the air coupler
into air high speed grinder.
4.3 Only lubricants recommended by the manufacturer shall be used.
4.4 Disconnect air supply from air inlet.
4.5 Insert the attached sockets ,adaptor or extension bar. Always use impact wrench sockets and accessories in good condition
and are intended for use with power tools.
4.6 Release the trigger in the case of an interruption of the energy supply.
4.7 This air impact wrench is designed for Right/Left rotating direction. Forward and reverse direction is controlled by pushing
the button noted. "F" (forward) right direction (clockwise), for tighten regular screw. "R"(reverse) left direction (counterclockwise),
for loosens regular screw.
5. Maintenance instruction
Air tools require lubrication throughout the life of the tool. The air motor and bearing uses compressed air to power the tool.
Because moisture in compressed air will rust the air motor, you must lubricate the motor daily.
Disconnect the tool from the air supply holding it so the air inlet faces up. Hold the trigger down and put 4 to 5 drops of air tool
oil or motor oil SAE1 0-20 in the air inlet. Holding the trigger down helps circulate oil in the motor.
Connect the tool to air supply, cover the exhaust port with a towel and run for a few seconds. Warning! Any excess oil in the
motor is immediately expelled from the exhaust port. Always direct exhaust port away from people or objects. Before connecting
the air hose, apply 4 to 5 drops of air tool oil SAE10-20 spindle oil at the air inlet. Also, every 3 to 4 hours of operation, oiling is
necessary.
Avoid storing the tool in a location subject to high humidity. If the tool is left as it is used, the residual moisture inside the tool can
cause rust. Before storing and after operation, oil the tool and run it for a short time. Regular inspection of spindles, threads, and
clamping devices in respect of wear and tolerances for location of abrasive products.
Disposal
If the tool is too seriously damaged to be used anymore. Recycle raw material instead of disposing as waste. The machine,
accessories and packaging should be sorted for environmental-friendly recycling. Check with your local authority or retailer
for recycling advice. Defective or worn out power tool must be recycled according to the Directive WEEE 2002/96/EEC.
SW-Stahl und Werkzeugvertriebs GmbH
Leverkuser Strasse 65
D-42897 Remscheid
Tel. +49 (0) 2191 / 46438-0
Fax +49 (0) 2191 / 46438-40
E-Mail: info@swstahl.de