HoMedics spa FS-250-EU Bedienungsanleitung Seite 2

IB-FS250-1118-04.qxp_Layout 1 06/11/2018 17:12 Page 2
P R O D U C T F E AT U R E S
Fig. 1
Fig. 1 Abb. 1
Spacious design:
Comfortably fits up to size
12/47 foot
Splash guard
Bubble Spa:
Enjoy a soothing and
rejuvenating bubble
massager
I N S T R U C T I O N S F O R U S E
1. Ensure that the unit is unplugged before filling with water. Fill with
warm water to the MAX fill line located on the inside of the tub.
NOTE: The water heater will only help to maintain the temperature
between 40-45 degrees. It will not heat cold water. For a warm water
massage, fill the unit with warm water.
2. Place the unit on the floor in front of a chair. It is recommended to place
the product on a towel.
3. Plug the unit into a 220-240 AC power supply.
4. Sit down and place your feet in the spa.
5. To operate the unit:
to activate vibration massage, press
to activate Bubble Massage + Keep Warm, press
Vibration and Bubble massage settings can be used separately or at the
same time. N.B. The keep warm function is automatically activated
when the bubbles are switched on. The vibration massage can be used
with or without water. The bubble massage + keep warm must only be
used with water.
6. To activate the water heater press
The water heater will heat the water to maintain the temperature
between 40-45°C. To deactivate the water heater press the button
again.
N.B. When filling the footspa use warm water, the heater is not
designed to heat the water from cold. Perception of temperature is
individual: If the water feels uncomfortably hot, turn off the heater and
allow to cool.
7. Enjoy a deep massage by sliding feet back and forth over the stimulating
nodes and rollers on the footspa floor. The fixing bracket from one side
will come away with the roller, take care not to lose this. To reassemble:
1. Insert the free end of the roller into the fixed bracket.
2. Carefully clip the other end, with the bracket attached, back into
place.
Magnetic therapy:
With 1000 gauss rating
Acu-nodes: stimulate the
acupressure points on the
sole of the foot.
the indicator light will show.
Max. fill line
Massage rollers x4:
Roll beneath your feet
for a deep penetrating
foot massage
Exfoliating
pumice stones
see Fig 4.
Touch controls
8. Move your foot over the exfoliating pumice stone to smooth the skin. To
change between the coarse and fine stone simple lift the attachment
and replace.
9. To turn off, press the buttons again to deactivate.
10. To empty: First, unplug the unit. Tip the unit, allowing water to pour out
along the drain spout (see fig.3). DO NOT pour water over the control
panel.
Caution: Do not fill water over the fill line. The fill line is marked on the
inside of the product: MAX
Note:
• To avoid injury and irreparable damage, always remain seated when using
this footspa. Never stand on or in the unit.
• NEVER use the bubble function without water. It is ok to use the vibration
function without water as a dry massager.
M A I N T E N A N C E :
Cleaning
Unplug the appliance and allow to cool before cleaning. Clean only with a
soft, slightly damp sponge.
• Do not immerse in any liquid to clean.
• Never use abrasive cleaners, brushes, glass / furniture polish, paint thinner
etc to clean
Storage
Place the appliance in its box or in a safe, dry, cool place. To avoid breakage,
DO NOT wrap the power cord around the appliance. DO NOT hang the unit by
the cord.
2 I GB
Fig. 2
Ergonomically angled base
for superior comfort
Fig. 3
Pouring spout for easy
water disposal
x2
Fig. 4
2 x interchangeable
pumice stones. Coarse: for
exfoliation. Smooth: for
polishing skin.
IB-FS
F
F
1
2
3
4
5
6
7