Mactronic FALCON EYE FWS0007 Kurzanleitung

WORKSHOP LAMP KIT
FWS0007
EN / SPECIFICATION
HEADLAMP
Light source COB Led + Red Led
Power supply Li-Po 3.7V 1200 mAh
MODES OUTPUT RUN TIME
HIGH 900 lm 1 h 30 min
MEDIUM 500 lm 3 h
LOW 100 lm 9 h
STROBE - -
COB LED HIGH 100 lm 10 h
COB LED LOW 50 lm 15 h
RED LED FLASHING - -
SENSOR MODE HIGH 900 lm -
SENSOR MODE LOW 500 lm -
Dimensions 64,5 x 43,3 x 40 mm
Weight 90,5 g
Impact resistance 1 m
WORKSHOP LIGHT
Light source COB Led
Power supply Li-Ion 3600 mAh
MODES OUTPUT RUN TIME
HIGH 500 lm 4 h
MEDIUM 250 lm 8 h
LOW 125 lm 16 h
Dimensions 64,5 x 43,3 x 40 mm
Weight 190 g
Impact resistance 1 m
Thank you for choosing a Mactronic® product. Proper operation and main-
tenance guarantee the product's high durability and reliability. Please read
the operating manual and keep it for reference, because it contains impor-
tant information about safety and operation of the product.
NOTICE
It is not recommended to use the flashlight for purposes other than in-
tended. The manufacturer explicitly voids the warranty if the flashlight has
been used for other than its intended purpose.
FLASHLIGHT OPERATION
WORK LAMP: To turn on the flashlight, press the right button located on the
front of the flashlight. The flashlight will turn on in low mode (LOW). Sub-
sequent button presses will cycle through the modes in the following order:
LOW → MEDIUM → HIGH → OFF. During operation and while charging, the
battery level is indicated by 4 blue LED lights. At the rear of the flashlight,
there is a strong magnet and a collapsible handle with a clip, allowing for
easy attachment of the flashlight to a work area without the need to hold
it in hand.
HEADLAMP: To turn on the headlamp, press one of the available power
buttons (either the right or left). Pressing the right power button will im-
mediately turn on the flashlight. Hold down the left power button for 3 se-
conds until the flashlight turns on. For the right power button, the available
DISTANCE
functions/modes are activated in the following sequence: LOW → MEDIUM
90 m
→ HIGH → STROBE → COB HIGH → COB LOW → RED LIGHT FLASHING
70 m → OFF. If the mode change button is not pressed for 8 seconds, the next
press will turn off the light. Restarting will cycle back to the first mode
30 m
in the sequence. To activate the motion sensor mode, hold down the left
-
power button for 3 seconds. The motion sensor mode is a standby mode
13 m
that allows you to turn the light on or off with a hand motion from the left
5 m
side in front of the headlamp, within a detection range of up to 4 cm. For
the left power button, the available functions are activated in the following
-
sequence: SENSOR MODE HIGH → SENSOR MODE LOW → SENSOR MODE
-
COB HIGH → SENSOR MODE COB LOW → OFF. If the button is not pres-
-
sed during mode change for 8 seconds, the next press will turn off the
headlamp. To reactivate the motion sensor mode, hold down the left button
for 3 seconds. After turning on or off, the headlamp will indicate the battery
level using 4 blue LED lights for 5 seconds. This battery level indicator is
located on the front of the housing.
CHARGING
WORK LAMP: To charge the device, uncover the rubber cover of the USB-C
port located at the bottom of the flashlight. Connect the provided USB-US-
B-C cable to a USB wall charger, a computer's USB port, or a Power Bank
station. Attach the other end of the cable to the USB-C port. The active
DISTANCE
charging process will be indicated by the illumination of the 4-step charging
25 m
indicator, where a flashing LED indicates the current level of charge. Once
18 m
the charging process is complete, all indicator LEDs will remain steadily lit.
10 m
After disconnecting the charging cable, cover the port with the rubber co-
ver to protect it. You can also partially charge other devices by connecting
them to the USB port of the flashlight. To do this, uncover the rubber cover
of the USB-C port located at the bottom of the flashlight. Connect the provi-
ded USB cable to the USB port of the flashlight. Attach the other end of the
cable to the device you want to charge. The active charging process of the
external device will be indicated by the 4-step charging indicator.
HEADLAMP: To charge the device, uncover the rubber cover of the USB-C
port located at the bottom of the headlamp. Connect the provided USB-
-USB-C cable to a USB wall charger, a computer's USB port, or a Power
Bank station. Attach the other end of the cable to the USB-C port of the
headlamp. The active charging process will be indicated by the illumination
of the 4-step charging indicator, where a flashing LED indicates the current
level of charge. When the charging process is complete, all indicator LEDs
will remain steadily lit. After disconnecting the charging cable, cover the
port with the rubber cover to protect it.
CAUTION!
Make sure you use only genuine parts designed for Mactronic® flashlight.
Using spare parts from other manufacturers may affect the quality and
parameters of the product. The rechargeable batteries used in this product
may be subject to re-processing. Pursuant to the EU's WEEE regulation,
storage batteries must not be disposed of with normal household waste.
Instead, they must be disposed of at designated battery collection points.
Contact the management of your local waste collection company for advice
on the required ways and types of re-processing, or other instructions.
GENERAL INFORMATION
Modifications and repairs:
Unless authorized by Mactronic® in writing, any modifications and user at-
tempts at home repairs will automatically void the warranty.
Mactronic® warranty:
Mactronic® covers the product with a 2-year warranty for any manufactu-
red defects in material and/or workmanship. The warranty does not cover
the product, rust, unauthorized modifications, improper storage, damage
from falls, improper handling, corrosion from leaking batteries, and use of
the product to its intended purpose.
USING AND HANDLING THE BATTERY
To reduce the risk of fire, electrocution or other bodily harm, carefully read
the flashlight's operating manual.
• Always make sure the battery's polarity is correct.
• Remove the batteries if the flashlight is stored for extended time.
• Do not recharge alkaline batteries.
• Do not dispose of the batteries in fire.
• Keep the batteries out of reach of the children.
• Do not force the batteries open.
• Keep the flashlight away from UV radiation, humidity and chemical
products.