BEDIENUNGSANLEITUNG
COMMUNICATION CENTER II
BZ990001
A. TECHNISCHE DATEN:
Spannungsversorgung:
empfohlenes Netzteil 24V, 1Amax
1,5-6W (max. im GPRS-Modus)
Leistungsaufnahme:
4, max. 24VDC, optional Zähleingang
Digitale Eingänge:
(S0 Schnittstelle, Impulsdauer 30 – 500ms, 1 – 1000 Impulse
pro Einheit)
Digitale
Ausgänge:
Wechselkontakt),
AC:
Dauerstrom=10A, max. kurzzeitiger Einschaltstrom=15A)
DC: 10A bis 30VDC, 0,3A bis 110VDC und 0,12A bis 220VDC,
Maximale Schaltleistung AC15 bei 230VAC: 500VA
Temperaturfühler:
on board; Genauigkeit 1°C (Achtung
auf Eigenerwärmung des Gerätes).
Quadband GSM/GPRS-Modul, GPRS class B, GSM
Modem:
class1 (1W@1800/1900MHz, 2W@850/900MHz)
Antennenstecker:
SMA female
Ethernet,
Schnittstellen:
Optionell=RS484)
Steckbare
Kompaktklemmen:
(starr/flexibel): 0,2-2,5mm²/0,2-2,5mm²
Klinge 0,6x3,5x100mm
Schraubendreher:
-20°C bis +50°C
Temperaturbereich:
Montage:
Hutschiene (Normschiene nach DIN EN50022)
Gehäuseabmessungen:
Unterteil PPO, Oberteil PC
Gehäusematerial:
B. ERSTE SCHRITTE:
1. Die SIM-Karte des CC in ein Mobiltelefon geben und den
PIN-Code ausschalten (zunächst den PIN-Code eingeben und
dann die SIM-Sperre aufheben).
Bei dieser Gelegenheit kann auch überprüft werden ob das
GSM-Netz am Standort stark genug ist (mindestens 3 von 5
Strichen auf der Anzeige – je nach Typ des Mobiltelefons).
2. Die beiden Seitenlaschen des CC anheben und das Gerät
öffnen, die SIM-Karte einsetzen.
Satz- und Druckfehler vorbehalten. Technische Änderungen möglich. / Subject to technical changes and misprints.
SCHRACK TECHNIK GMBH
Seybelgasse 13, A-1230 Vienna, TELEFON: +43 1/86685-0
EMAIL: info@schrack.com, INTERNET www.schrack.com
12-24VDC
(max.
2
(Relaisausgänge
10A
bei
250VAC
Seriell
(Standard=RS232;
Leitungsquerschnitt
105x86x60mm (LxBxH)
USER MANUAL
COMMUNICATION CENTER II
BZ990001
A. TECHNICAL DATA
30VDC);
Power supply:
power supply unit 24V, 1Amax
Power consumption:
Digital Inputs:
interface, pulse duration 30 – 500ms, 1 – 1000 pulses per
unit)
mit
Digital Outputs:
(max.
contacts), AC: 10A at 250VAC (max. continuous current =5A,
max. inrush current =10A)
DC: 5A at 30VDC, 0,3A at 110VDC and 0,12A at 220VDC,
maximum switching capacity AC15 at 230VAC: 500VA
Temperature sensor:
please contact Schrack Technik.
Quadband GSM/GPRS-Modul, GPRS class B, GSM
Modem:
class1 (1W@1800/1900MHz, 2W@850/900MHz)
Antenna connector:
Interfaces:
optionally=RS484)
Pluggable
2,5mm²/0,2-2,5mm²
Screwdriver:
Temperature range:
Assembly:
top-hat rail (standard DIN EN50022)
Dimensions of the casing:
Material of the casing:
B. FIRST STEPS
1. Insert the Communication Center's SIM card in your mobile
phone and deactivate the PIN code (by entering the SIM-code
and unlocking the SIM-lock).
Use this opportunity to detect the actual transmitting power
of your GSM provider. (3 to 5 lines should be displayed –
depending on the type of your mobile phone).
2. Lift the Communication Center's side plates, open the
device and insert the SIM card.
Seite / Page 1
12-24VDC (max. 30VDC); recommended
1,5-6W (max. in GPRS mode)
4, max. 24VDC, optionally: counter input (S0
2 (relay outputs with change-over-
external sensor for RS232 available –
SMA female
Ethernet,
serial
clamp:
wire
guage
blade: 0,6x3,5x100mm
-20°C to +50°C
105x86x60mm (LxWxH)
bottom part PPO, upper part PC
Modem
SIM
last update: 17.08.2009
II
(standard=RS232;
(fixed/flexible):
0,2-
BZ990001
Version 1.2