Cleaning And Care; Technical Data - Toolcraft Max850 Bedienungsanleitung

Then press the filling tip of the lighter gas cartridge against the filling valve. The liquefied gas
now flows into the gas tank of the hot-gas burner. End the filling procedure after 2 to 3 seconds.
This filling process can be repeated 2 or 3 times.
Stop the filling process immediately if gas escapes. A gas-air mixture could arise
which could explode. Make sure that the room has been well ventilated before you
ignite hot-gas burners or other sources of ignition.
Wait for at least 3 minutes after filling before using the hot-gas burner, so that the
gas refill can stabilise.
8 Operation
8.1 Preparation
Hold the hot-gas burner in such a way that the flame exit opening (5) points away from you.
Also hold it so that the grip points downward.
Turn the gas volume knob (4) all the way to the left (counter-clockwise).
Move the sliding switch (1) for child safety upward in the direction of the gas volume control.
This lowers the barrier for the push button (2).
8.2 Igniting the flame
Press the push button (2) and hold it down firmly. The exiting gas is thereby ignited by the
integrated piezo-ignition; the flame should now burn.
If only gas comes out and no flame, let go of the push button (2) and press it again.
8.3 Adjusting the size of the flame
You can adjust how much gas comes out and how large the flame is with the gas volume
control (4).
If you turn the dial to the left counter-clockwise (labelled "+"), the volume of gas increases and
the flame gets larger.
If you turn the dial to the right clockwise (labelled "-"), the volume of gas decreases and the
flame gets smaller.
8.4 Turning off flame, ending operation
Release the push button (2) ; the gas vent is closed and the flame goes out.
Move the sliding switch (1) for child safety downward in the direction of the gas tank. The
push button (2) is thereby locked.
Place the hot-gas burner in the provided stand and let it cool down completely.
Once the hot-gas burner is completely cooled off, it can be stored in a clean, dry location.
Make sure that the hot-gas burner is always stored upright. Use the provided stand for this
purpose.
8.5 Constant function
A constant function can be achieved with the locking knob (3), so that you can release the push
button and the hot-gas burner continues to run nevertheless.
Proceed as follows:
Press the push button (2) and hold it down. The exiting gas is thereby ignited by the inte-
grated piezo-ignition; the flame should now burn.
If only gas comes out and no flame, let go of the push button (2) and press it again.
Keep holding the push button (2) down. Now press the locking knob (3) for the constant
function and hold it down firmly.
Release the push button (2).
The flame continues to burn without you needing to push a button on the hot-gas burner.
To turn off the flame, press the push button (2) so that the locking knob (3) pops out.
Move the sliding switch (1) for child safety downward in the direction of the gas tank. The push
button (2) is thereby locked.
Place the hot-gas burner in the provided stand and let it cool down completely.
9 Troubleshooting
Flame does not burn or goes out again immediately:
Turn the gas volume knob (4) all the way to the left (counter-clockwise) before you ignite
the hot-gas burner. Only after a successful ignition should you adjust the desired flame
intensity.
If the dial is turned too far to the right, too little gas comes out and a flammable mixture does
not form.
The gas tank is empty and must be refilled.
The push button (2) for the ignition function cannot be pressed:
Move the sliding switch (1) for child safety upward in the direction of the gas volume control.
This lowers the barrier for the push button (2).
Gas comes out during filling:
Use the right adapter during filling. Normally, this is provided with every lighter gas car-
tridge.

10 Cleaning and care

Important:
– Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions.
They damage the housing and can cause the product to malfunction.
– Do not immerse the product in water.
Use a dry, lint-free cloth to clean the product.
Remove any residual gas before storing the hot-gas burner.
If there is a leak on your appliance (smell of gas), take it outside immediately into a well
ventilated flame free location where the leak may be detected and stopped. If you wish to
check for leaks on your appliance, do it outside. Do not try to detect leaks using a flame,
use soapy water.
If the appliance is damaged, please scrapped it directly.
This appliance should only be used with any type 200 cartridges marked "Butane" complying
with EN 417.CAUTION: Kitchen torch, for kitchen use only.
Use only in well-ventilated area.
Gas containers shall be changed in a well ventilated location, preferably outside, away from
any sources of ignition, such as naked flames, pilots, electric fires and away from other people.
Use only in well-ventilated area.
For the supply of combustion air; and to avoid the dangerous building up of un-burnt gases for
appliances not fitted with a flame supervision device.
11 Disposal
At the end of its service life, dispose of the product in accordance with applicable
regulatory guidelines.
You thus fulfill your statutory obligations and contribute to the protection of the en-
vironment.

12 Technical data

Flame temperature ....................... max. approx. 1300 °C
Gas tank ....................................... 36 ml
Operating duration ........................ with one gas filling, max. approx. 150 min
Dimensions (L x W x H) ................ 155 x 75 x 195 mm
Weight .......................................... approx. 350 g (without base stand)
Nominal rate ................................. 1.4 kW(100 g/h)
Nozzle dimension ......................... 0.18 mm
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights in-
cluding translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represents the technical status at the time of printing.
Copyright 2024 by Conrad Electronic SE. *588386_V2_0124_02_dm_mh_en_(1)