Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Read the complete manual before carrying out the installation and activating the system. Keep the
manual for future reference.
1. DESCRIPTION
This DALI potentiometer or DALI slave dimmer is used to control DALI controlled light luminaires. The dimmer
can be set to control all luminaires in a certain DALI group or set in broadcast mode, to control all DALI controlled
devices simultaneously. The rotary dimmer can also be used in combination with the Niko DALI addressable
detectors to manually dim the light.
This dimmer is not equipped with a built-in power supply for the DALI bus. Use the Niko DALI power supply
(350-70985) for this purpose.
2. MOUNTING
Danger: do not install the dimmer while it is connected to the mains voltage supply. Do not connect the device
to the mains voltage until installation has been completed (including installation of the central plate and flush
surround plate).
1. Connect the dimmer as shown in the wiring diagram in figure 2.
2. Mount the dimmer in a flush-mounting box with a flush-mounting depth of minimum 40 mm.
3. Mount all components as shown in figure 1.
3. SETTINGS
3.1. Determine the controlled light points
The dimmer can either be set to control 15 DALI groups or zones separately, or set in broadcast mode to control
all DALI controlled devices simultaneously (factory setting). Use the DIP switches to choose what you want to
control (see table below). Connect the dimmer to the same DALI bus. Set the DIP switch to DALI group 1. Check
which DALI luminaire or light group lights up. If this is not the desired luminaire or light group, try group 2 etc.
DALI group
All groups (broadcast, factory setting)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
3.2. Set the dimming speed
You can manually adjust the dimming speed (the 'fade rate') using the dimmer. The procedure is as follows:
1. Switch on the DALI group of which you want to adjust the dimming speed.
2. Set the DIP switches to the desired dimming speed according to the table below.
Dimming speed (number of steps per
second)
No dimming
357.796
253.000
178.898
126.500
89.449
63.250
44.725
31.625
22.362
15.813
11.181
7.906
5.591
3.953
2.795
3. Press and hold the rotary button for 8 seconds until the lights in the DALI group switch off.
The dimming speed is now adjusted and saved.
Please note: do not forget to return the DIP switches to their correct position afterwards (broadcast or desired
DALI group, see § 3.1).
4. OPERATION AND USE
Switch the light on or off with a light push on the rotary button. Increase the light intensity by turning the button
clockwise. Decrease the light intensity by turning the button anti-clockwise.
If the selected DALI group is switched off and you turn the rotary button clockwise, the group will switch on at
maximum light intensity. If the selected DALI group is switched off and you turn the rotary button anti-clockwise,
the group will switch on at minimum light intensity.
nv Niko sa Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: support@niko.be — www.niko.eu
PM310-0210xR16512
Position DIP switches
1
2
3
4
0
0
0
0
1
0
0
0
0
1
0
0
1
1
0
0
0
0
1
0
1
0
1
0
0
1
1
0
1
1
1
0
0
0
0
1
1
0
0
1
0
1
0
1
1
1
0
1
0
0
1
1
1
0
1
1
0
1
1
1
1
1
1
1
Position DIP switches
1
2
3
4
0
0
0
0
1
0
0
0
0
1
0
0
1
1
0
0
0
0
1
0
1
0
1
0
0
1
1
0
1
1
1
0
0
0
0
1
1
0
0
1
0
1
0
1
1
1
0
1
0
0
1
1
1
0
1
1
0
1
1
1
1
1
1
1
5. TECHNICAL DATA
power supply voltage
power consumption
DALI standard
groups/zones
dimming speed
connection terminals
ambient temperature
marking
6. WARNINGS REGARDING INSTALLATION
• The installation should be carried out by a registered installer and in compliance with the statutory regulations.
• This user manual should be presented to the user. It should be included in the electrical installation file,
and it should be passed on to any new owners. Additional copies are available on the Niko website or via
the Niko support service.
• During installation, the following should be taken into account (non-exhaustive list):
- the statutory laws, standards and regulations.
- the technology currently available at the time of installation.
- this user manual, which only states general regulations and should therefore be read within the scope
of each specific installation.
- the rules of proper workmanship.
This product complies with all of the relevant European guidelines and regulations. If applicable, you can find
the EU declaration of conformity regarding this product at www.niko.eu.
7. NIKO SUPPORT
In case of doubt or for the specific exchange procedure in case of a possible defect, contact the Niko support
service in Belgium at +32 3 778 90 80 or your wholesaler/installer. Contact details and more information can
be found at www.niko.eu under the "Help and advice" section.
8. GUARANTEE PROVISIONS
• The period of guarantee is four years from the date of delivery. The delivery date is the invoice date of
purchase of the product by the consumer. If there is no invoice, the date of production applies.
• The consumer is obliged to inform Niko in writing about the non-conformity, within two months after
stating the defect.
• In case of a non-conformity, the consumer only has the right to a product repair or replacement free of
charge, which shall be decided by Niko.
• Niko shall not be held liable for a defect or damage resulting from incorrect installation, improper or careless
use, incorrect operation, transformation of the product, maintenance that does not adhere to the maintenance
instructions or an external cause, such as damage due to moisture or overvoltage.
• The compulsory regulations of the national legislation concerning the sale of consumer goods and the
protection of the consumer in the countries where Niko sells, directly or via sister companies, subsidiaries,
chain stores, distributors, agents or permanent sales representatives, take priority over the above-mentioned
rules and regulations.
Do not dump this product with the unsorted waste. Bring it to a recognised waste collection point. Together with producers
and importers, you have an important role to play in the advancement of sorting, recycling and reusing discarded electrical
and electronic appliances. In order to finance the waste collection and processing, the government levies a recycling
contribution in some cases (included in the purchase price of this product).
310-0210X
via the DALI bus (not built-in)
6 mA
EN 60929, Annex E
15 separately or all at once
adjustable
2 x 2.5 mm²
+ 5 – +50 °C
CE marked
3
EN
Werbung
