Herunterladen Diese Seite drucken
MODE D'EMPLOI
INSTALLATION INSTRUCTIONS
BEDIENUNGSANLEITUNG
GEBRUIKSAANWIJZING
EF30035ENC_NTALL
vE_230130
EF30035ENC
(*) Forces de retenue maximales pour des mises en œuvre respectant les conditions de pose optimales
Maximal theoretical holding forces for implementations fulfilling optimal installation conditions
a
NOMENCLATURE
BILL OF
MATERIAL
LIEFERUMFANG
INHOUD
EF30035ENC
1 x
INSTRUCTIONS GENERALES AVANT LE MONTAGE
GENERAL INSTALLATION INSTRUCTIONS
FR
- Utiliser ce matériel uniquement pour une application adaptée.
- Le fabricant n'est pas responsable des dommages éventuels causés par une utilisation contraire aux dispositions de sécurité.
- Le montage, la maintenance et les réparations doivent être réalisés par un personnel spécialisé et autorisé.
EN
- Use this equipment only for an adapted application.
- The manufacturer cannot be held responsible for possible damage caused when usual security requirements are not fulfilled.
- Mounting, maintenance and repair must be carried on by a skilled and authorized staff.
DE
- Dieses Material nur für vorgesehene Anwendungen einsetzen.
- Der Hersteller leistet keine Gewähr für Schäden die durch fehlerhafte Montage oder nicht einhalten von Sicherheitsvorschriften entstehen.
- Die Montage, die Wartung und Reparaturen dürfen nur durch sachkundiges Personal durchgeführt werden.
NL
- Alleen dit materiaal gebruiken voor een aangepaste toepassing.
- De fabrikant is niet verantwoordelijk voor eventuele schade die door een tegenstrijdig gebruik aan de veiligheidsbeschikkingen worden veroorzaakt.
- De installatie, het onderhoud evenals de reparaties moeten door een gespecialiseerd en bevoegd personeel verwezenlijkt worden.
www.sewosy.com  Depuis la France : 0 891 89 95 97 (service 0,80€ / min + prix appel) -  From abroad: +33 (0)3 90 59 02 20
Les indications, photographies, images ou schémas présents sur cette notice n'engagent pas la société SEWOSY et n'ont aucune valeur contractuelle
The informations, photographs, images, drawings contained in this leaflet does not engage the responsibility of SEWOSY and have no contractual value
24V DC
2,5 kg
240 mA
-15 / +20%
b
c
d
2 x
1 x
1 x
FR
SACHET
PLASTIQUE
VENTOUSE ELECTROMAGNETIQUE A ENCASTRER
EF30035ENC
300 DaN
6 W
(*)
Voor een optimale theoretische houdkracht, instellingsvoorwaarden 100% respecteren
e
f
g
h
1 x
1 x
4 x
4 x
ALLGEMEINE ANWEISUNGEN VOR DER MONTAGE
MONTAGE INLICHTINGEN VOOR INSTALLATIE
PAPIER OU
CARTON
MORTICE ELECTROMAGNETIC LOCK
uP -FLÄCHENHAFTMAGNET
INBOUW VERGRENDELMAGNEET
- 10° C
42
+ 55° C
(*) Maximale theoretische Haftkräfte unter optimalen Montagebedingungen
i
j
k
3 x
2 x
1 x
1 x
CNPP
PV N° SD 230004
l
m
n
1 x
1 x
2 x
1/4
loading

Inhaltszusammenfassung für sewosy EF30035ENC

  • Seite 1 PLASTIQUE www.sewosy.com  Depuis la France : 0 891 89 95 97 (service 0,80€ / min + prix appel) -  From abroad: +33 (0)3 90 59 02 20 Les indications, photographies, images ou schémas présents sur cette notice n’engagent pas la société SEWOSY et n’ont aucune valeur contractuelle...
  • Seite 2 CONFIGURATIONS DE POSE MONTAGEZEICHNUNGEN INSTALLATION DIAGRAMS MONTAGE CONFIGURATIES 14,50 MONTAGE AVEC PATTES DE FIXATION MOUNTING WITH MOUNTING BRACKETS MONTAGE MIT MONTAGEPLATTEN MONTAGE MET BEVESTIGINGSSTEUNEN 36,50 Insérer la rondelle caoutchouc (j) entre les rondelles métalliques (i) en évitant de serrer l’ensemble trop fortement afin de conserver la mobilité de la contreplaque. Insert the rubber washer (j) between the steel washers (i) and do not screw too tighltly to keep the armature plate slightly loose.
  • Seite 3 DIMENSIONS ABMESSUNGEN AFMETINGEN 24V DC RACCORDEMENT CONNECTION Position usine ANSCHLUßPLAN Factory setting AANSLUITING Werkeinstellung Standaardpositie 24V DC 12V DC Attention - Caution : Achtung - Opgepast : - Veiller à respecter la polarité indiquée. - Anschlußpolarität beachten. - Höhe der Betriebsspannung beachten. - Utiliser une tension conforme à...
  • Seite 4 Blzd. 4 ALLEEN VOOR FRANKRIJK : NF S 61937 CONFORMITY - 24V DC NF S 61937 KONFORMITEIT - 24V DC Montage des presse-étoupes Vers alimentation 24V DC Ventouse EF30035ENC Câble type C2 minimum 1 mm Ex. : Contreplaque U1000 RO2V 2 x 1,5 mm Passage des câbles...