expander elite Gebrauchsanweisung Seite 9

OPERATION MANUAL
UNFOLDING THE PRAM
vividly the handle up until the folding mechanism is locked
(Fig. 2, 3).
NOTE! Before starting to use the pram, make sure that it has
been correctly unfolded.
ASSEMBLING AND DISASSEMBLING THE REAR WHEELS
To disassemble the rear wheels, press down the button in the
central part of the wheel (Fig. 4) and remove the wheels from the
axle (Fig. 5). To assemble them again, press the button down and
slide the wheels onto the axle till they get locked.
NOTE! Before starting to use the pram, make sure that all the
wheels have been assembled correctly.
ASSEMBLING AND DISASSEMBLING
SWIVELLING WHEELS
In order to assemble the front wheels, force their axles in the
ends of the front legs, until you hear a characteristic "click" (Fig.
6). In order to disassemble the wheels press down the button at
the upper part of the swivelling mechanizm (Fig. 7) and slide the
wheel axle in.
The swivelling front wheels may be locked for going straight. In
order to lock the wheels, move down the plastic lever in the front
part of the swivelling mechanism (Fig. 8).
HANDLE HEIGHT ADJUSTMENT
It is possible to adjust the pram handle height. To perform the
adjustment, press down the round buttons on both sides of the
handle at the upper part, and then adjust the right height (Fig. 9).
PARKING BRAKE
The pram is equipped with a rear parking brake. To engage the
brake, press its lever down (Fig. 10). In order to disengage it, lift
the lever.
NOTE! Before starting to push the pram, make sure that the
brake has been disengaged.
NOTE! Always engage the safety brake, when you leave the
pram on an inclined surface.
NOTE! The brake is not designed for slowing down. It should be
engaged after the pram has been stopped completely.
NOTE! The pram is not designed for running.
ATTACHING AND REMOVING THE CARRYCOT
In order to attach the carrycot press it into the pram frame so
that the adapters on both sides of the carrycot lock onto the
automatically.
ATTENTION! Make sure the carrycot is attached correctly prior
to use. To remove the carrycot press the buttons on the adapters
ASSEMBLING AND DISASSEMBLING THE SEAT
NOTE! Before assembling the seat fasten it by connecting metal
fasteners to metal rivets covered under the fabric covers on both
The seat should be assembled and disassembled the same way
as for the bassinet (see ASSEMBLING AND DISASSEMBLING
THE BASSINET Fig. 13a, 13b, 14).
The seat may be assembled with its front and back facing the
THE FRONT
movement direction (Fig. 14a, 14b).
ADJUSTING THE LEG REST
The pram is equipped with an adjustable leg rest. To move
it to the right position, press down the buttons on its both sides
(Fig. 15).
SAFETY BAR
To attach the bar, insert its tongues into the slots in armrests.
To remove it, push the buttons located on the bottom of the slots
The bar is adjustable. You can detach one of its ends and move it
NOTE: The bar is an extra element and you must still use the
RESTRAINT SYSTEM
The seat is equipped with a 5-point restraint system (Fig. 18).
It should be used from the moment a baby starts to sit by itself.
Unfasten the belts, by releasing the forks from the central buckle,
to the baby's body, without oppressing it, and then fasten the forks
of all the belts to the central buckle.
NOTE! Always use the restraint system, if the baby can sit by
itself.
ADJUSTING THE BACKREST
The backrest position is adjusted using a special strap and a
buckle. To lower the backrest push the
button on the buckle and pull it down. To raise the backrest push
RECLINING CARRYCOT SUPPORT
The carrycot is equipped with headrest adjustment functionality.
In order to set the required headrest position, pull the mattress
FOLDING THE PRAM
To fold the pram frame, stand behind the pram from the handle
side, pull up the plastic levers on both sides of the handle (Fig.
21), and push the handle down until the frame folds completely
(Fig. 22, 23).
9