Montagehinweise
Um alle Möglichkeiten des Produktes optimal ausschöpfen zu
können, lesen Sie bitte sorgfältig die nachfolgenden Installations
hinweise.
1. Stecken Sie den Rundstecker des WIFI CONTROL in den Multi
funktionsanschluß (Control Input) des DSPProdukts.
2. Verbinden Sie die Masseleitung des Anschlusskabels (Ground /
braun) mit einem Massepunkt am KfzChassis oder Massean
schluss eines DSPs / Verstärkers.
3. Schließen Sie den +12 V DauerplusAnschluss (orange) an eine
+12 V Spannungsquelle an.
Achtung: Achten Sie auf eine korrekte Polung, um Beschädi
gungen am WIFI CONTROL und / oder dem DSP / Verstärker / der
KfzElektronik zu vermeiden.
4. Optional: Schließen Sie die separat erhältliche URC.3 Fernbedie
nung an den MiniDINAnschluss des WIFI CONTROL.
Hinweis: Die Bedieneinheit DIRECTOR ist nicht kompatibel mit
dem WIFI CONTROL.
Konfiguration des WIFI CONTROLs
Zur Inbetriebnahme des Gerätes muss zuerst der Betriebsmodus
(AP- oder Client-Mode) konfiguriert werden. Hierzu befindet sich das
WIFI CONTROL im Auslieferungszustand im Config-Modus und baut
ein eigenes WLAN auf. Der Config-Modus kann auch durch das drü
cken des Reset-Tasters für 5 Sekunden aktiviert werden.
1. Schalten Sie Ihr Soundsystem ein.
2. Öffnen Sie das WLAN-Menü Ihres PCs / Tablets / Smartphones
und stellen eine Verbindung mit dem Netzwerk „WIFI CONTROL
Config" her.
3. Laden Sie die WIFI CONTROLApp (ab iOS 11 / Android 7) aus
dem App Store oder Google Play auf Ihr Mobilgerät und installieren
diese. Nach erfolgreicher Installation starten Sie die App. Alterna
tiv öffnen Sie Ihren Webbrowser und geben „192.168.4.1" in die
Adresszeile ein. Nun öffnet sich die Web-App des WIFI CONTROL.
4. Konfigurieren Sie das WIFI CONTROL als Access Point (AP-Mo
de / empfohlene Konfiguration) oder als Client (Client-Mode).
APMode: Im APMode erstellt das WIFI CONTROL ein eigenes
WLAN-Netzwerk. Der Vorteil ist, dass jederzeit und überall auf das
DSP-Gerät zugegriffen werden kann. Zur Konfiguration gehen Sie
wie folgt vor:
1. Legen Sie unter SSID einen Namen für das Netzwerk fest.
2. Legen Sie ein Passwort fest und speichern die Einstellung durch
klicken auf den „Save"-Button.
3. Öffnen Sie erneut das WLAN-Menü Ihres PCs / Tablets / Smart
phones und stellen eine Verbindung mit dem neu erstellten
Netzwerk her. Nun können Sie Ihr DSP-Produkt über das WIFI
CONTROL konfigurieren und steuern.
ClientMode: Im ClientMode verbindet sich das WIFI CONTROL
mit einem bestehenden Netzwerk und nutzt dieses. Der Vorteil die
ser Konfiguration besteht darin, dass das WIFI CONTROL einma
lig konfiguriert werden muss und an verschiedenen DSP-Geräten
genutzt werden kann. Gehen Sie zur Konfiguration wie folgt vor:
1. Wählen Sie unter dem Punkt „SSID" das Netzwerk aus, in
welches sich das WIFI CONTROL einbinden soll.
2. Geben Sie das Passwort des Netzwerks ein.
3. Schließen Sie den Konfigurationsvorgang durch klicken auf den
WIFI CONTROL
„Save"-Button ab. Das WIFI CONTROL verbindet sich nun im
mer automatisch mit dem ausgewählten Netzwerk.
Verbinden mit dem DSP PC-Tool
1. Starten Sie die DSP PC-Tool Software (ab Version 4.50)
2. Stellen Sie auf der Startseite den Button auf „WIFI". Die Software
erkennt nun automatisch das mit dem WIFI CONTROL verbun
dene Gerät. Wichtig: Beide Geräte müssen sich im gleichen Netz
werk befinden.
3. Wählen Sie das zu konfigurierende Gerät aus und bestätigen die
Auswahl durch das Klicken auf den „Connect Button". Sie können
die Konfiguration jetzt starten.
Starten der Fernbedienungs-Funktion
Hinweis: Die FernbedienungsFunktion ist nur bei Geräten mit ACO
Plattform verfügbar.
Zusätzlich muss die FernbedienungsFunktion zuerst noch einmalig
im DCM-Menü der DSP PC-Tool Software aktiviert werden. Dazu ak
tivieren Sie bitte die „WIFI CONTROL" unter den Fernbedienungs
einstellungen.
1. Stellen Sie mit Ihrem PC / Tablet / Smartphone eine Verbindung
mit dem Netzwerk des WIFI CONTROL her (Name und Passwort
wie zuvor bei der Konfiguration des WIFI CONTROL festgelegt).
2. Öffnen Sie die WIFI CONTROL-App. Alternativ öffnen Sie den
Webbrowser und rufen die Seite „192.168.4.1" auf. Nun können
Sie ihr Gerät fernsteuern.
Reset-Taster
Wird der Reset-Taster 5 Sekunden gedrückt, wechselt das WIFI
CONTROL in den Config-Modus; ab 10 Sekunden wird es resettet.
Installation instructions
To secure a proper function of the device read this manual carefully
and follow all installation instructions.
1. Insert the circular plug of the WIFI CONTROL into the multi-func-
tional input (Control Input) of the DSP product.
2. Connect the ground wire of the connection cable (Ground / brown)
to a ground terminal of the vehicle or ground connector of a DSP /
amplifier.
3. Connect the permanent +12 V wire of the connection cable
( orange) to a +12 V source.
Attention: Check the polarity prior to the installation in order to
prevent damages of the WIFI CONTROL and / or DSP / amplifier /
battery or other equipment.
4. Optional: Connect the separately available remote control URC.3
to the WIFI CONTROL`s MiniDIN connector.
Note: The remote control DIRECTOR is not compatible with the
WIFI CONTROL.
Configuring the WIFI CONTROL
After the first start-up the operating mode (AP- or Client-Mode) needs
to be configured. Therefore the WIFI CONTROL is initially setup in
Config Mode and opens an own WiFi network. The Config-Mode can
also be activated by pushing the reset pushbutton for 5 seconds.
1. Start your sound system.
2. Open the WiFi menu of your PC / Tablet / Smartphone and estab-
lish a connection to the network "WIFI CONTROL Config".
3. Download the WIFI CONTROL app (as of iOS 11 and Android 7)
from the App Store or Google Play to your mobile device and in-
stall it. After the installation process has been successfully com-
pleted, start the app. Alternatively open your web browser and
enter "192.168.4.1" in the address bar. The Web-App of the WIFI
CONTROL will open up.
4. Configure the WIFI CONTROL as access point (AP-Mode / rec-
ommended configuration) or as client (Client-Mode).
AP-Mode: The WIFI CONTROL opens up its own WiFi network
in AP-Mode. This mode lets you access the DSP anywhere and
anytime. Proceed as follows:
1. Specify a name for the network in the SSID input field.
2. Set a password and save the settings by clicking on the "Save"
button.
3. Reopen the WiFi menu of your PC / tablet / smartphone and
connect to the newly created network. Now you are able to con-
figure and control your DSP product via the WIFI CONTROL.
Client-Mode: In client mode the WIFI CONTROL connects to an
existing WiFi network. This mode allows you to connect the con-
figured WIFI CONTROL to any DSP within the range of your exist-
ing WiFi. Proceed as follows:
1. Select the network from the "SSID" drop-down list in which the
WIFI CONTROL should be integrated.
2. Enter the password of the network.
3. Complete the configuration process by clicking on the "Save"
button. The WIFI CONTROL now always automatically con-
nects to the selected network.
Connecting the DSP PC-Tool
1. Start the DSP PC-Tool software (as of version 4.50)
2. Toggle the button to "WIFI" which is displayed in the launcher.
The software now automatically detects the device which is con-
nected to the WIFI CONTROL. Important: The computer and the
WIFI CONTROL needs to be in the same network.
3. Select the device which should be configured and click the "Con-
nect Button". You can now start your configuration.
Starting the remote control function
Note: The remote control feature is only available for devices with
ACO platform. To activate the remote control function select the
"WIFI CONTROL" option in the remote control adjustments of the
DSP PC-Tool.
1. Connect your PC / Tablet / Smartphone to the network of the WIFI
CONTROL (name and password as determined during the WIFI
CONTROL`s configuration process).
2. Start your WIFI CONTROL app. Alternatively start your web
browser and open the web site "192.168.4.1". You can now re-
motely control your device.
Reset pushbutton
If the button is pressed for 5 seconds the WIFI CONTROL activates
its Config Mode. Pressing the button longer than 10 seconds will
reset the unit.
*Android is a trademark of Google LLC. Google Play and the Google Play logo
are trademarks of Google LLC.