Verwandte Anleitungen für Q Acoustics Q60WB
Inhaltszusammenfassung für Q Acoustics Q60WB
- Seite 1 3 0 6 0 S & 7 0 6 0 S S U B W O O F E R W A L L B R A C K E T I N S T A L L A T I O N I N S T R U C T I O N S Q 6 0 W B Designed and engineered in the United Kingdom.
- Seite 2 Introduction Thank you for purchasing Q Acoustics. This manual is intended to take you through setup and installation and will help provide optimum performance from the product. Please read the instructions, important safety information and warnings carefully before installation and use, to ensure the safe and satisfactory operation of this product.
- Seite 3 Step 1 Stick the vibration damping pad to the wall bracket in the position shown below. NOTE: The 3060S requires 2 vibration damping pads. The 3060S requires 2 vibration pads Step 2 Position your sub bracket and mark screw hole positions ensuring the bracket is perfectly horizontal.
- Seite 4 Step 3 Screw the bracket to the wall (fixings not provided) ensuring the wall and fixing method are sufficient to support the total load. Step 4 Place the sub on the bracket by lining up the front feet with the screw holes and holding the sub back flat against the vibration damping pad.
- Seite 5 Step 5 Loosely screw in the front 2 screws but DO NOT TIGHTEN FULLY. Step 6 Align the rear screws and screw in loosely.
- Seite 6 Step 7 Tighten all 4 screws evenly until the sub is sitting flat on the base of the bracket. The bracket is designed to flex as you tighten the screws, holding the sub tightly against the vibration damping pad. Step 8 Refer to the subwoofer full manual to complete the installation of your system.
- Seite 7 1. Schritt: Bringen Sie den Schwingungsdämpfer in der gezeigten Position an der Wandhalterung an. Hinweis: Für den 3060S sind zwei Schwingungsdämpfer erforderlich. 2. Schritt: Legen Sie die gewünschte Position der Subwoofer-Halterung an der Wand fest und markieren Sie die Position der Befestigungsschrauben.
- Seite 8 Fase 5: Allentare 2 viti anteriormente ma NON ALLENTARLE COMPLETAMENTE. Fase 6: Allineare le viti posteriori e avvitarle leggermente. Fase 7: Stringere tutte e 4 le viti fino a quando il subwoofer è posizionato in piano sulla base della staffa. La staffa è progettata per flettersi man mano che si avvitano le viti, mantenendo il subwoofer fermamente contro il dispositivo di smorzamento delle vibrazioni.
- Seite 9 Шаг 1. Прикрепите демпфирующую накладку к настенному кронштейну в указанном положении. ПРИМЕЧАНИЕ. для модели 3060S требуется 2 накладки. Шаг 2. Установите дополнительный кронштейн и отметьте места для винтовых отверстий таким образом, чтобы кронштейн располагался точно горизонтально. Шаг 3. Привинтите кронштейн сабвуфера к стене (крепления не входят в комплект поставки) и убедитесь, что стена и метод крепления достаточно...
- Seite 10 Q A C O U S T I C S . C O . U K Our policy is one of continuous product improvement. We reserve the right to change the designs and specifications without notice. This document contains information that is subject to change without notice Q16482-IS_r0...
- Seite 11 3000i Speaker Stand Pair Suitable for 3010i and 3020i speakers MA NUAL...
- Seite 12 3000i Speaker Stand Parts Assembly Instructions...
- Seite 13 3000i Speaker Stand...
- Seite 14 Q3000i Speaker Stands piastrelle, ecc utilizzare i piedi a cupola. Per evitare danni, English quando le punte vengono installate avere cura di inserire Warning il supporto dove non è possibile fare segni su arredi o Do not use close to a strong heat source – radiators, .