Skan Holz Basel 1 Bedienungsanleitung

Basel 1 420 x 300cm
Important information for your wood panel cabin
Please check the construction set for completeness using the position list in good time before starting con-
struction or commissioning your construction team. If individual parts are defective or missing, we will deliver
these as quickly as possible. However, we cannot refund the costs for any resulting construction delays to a
construction company.
Please understand that we cannot assume any guarantee fort he following defects:
- incorrect storage before assembly
- incorrect anchoring with the ground or inadequate foundation (foundation according to statics)
- damage due to erection errors, e. g. the house is not level or not right-angled
- damage through a higher level of snow burden than statically envisaged. Recommendation: lad relief of
the roof by removing the snow layer
- storm damage (insurance cases) or violent destruction
- damage through any alteration to the design by the client
- natural formation of cracks, branch holes, twisting, decolouration or similar modification (natural process;
has no influence on the statics)
Storage tips before assembly:
- store pallet on a level and dry surface.
- protect against sunshine and dampness; wood can warp drastically in a loose condition!
Maintenance tips:
Please observe the attached information sheet "Care instructions/Colour treatment".
General tips and refers to:
-
1
As the house is exposed constantly to the weather, it is necessary to lay a further welding line. You have to make
it for your own. We recommend clearing the roof during heavy snowfall!
-
2 A possibly desired installation of a rain gutter must be done by the building contractor; for this the roofing boards
must be cut to the right length.
-
1 Foundation according (to the structural calculations, not included in the scope of delivery): concrete C25/30,
strip foundation: w/h = 30/90cm, each 2 Ø 12 top and bottom, bow Ø 6, e < 20cm. Bottom panel:
t=14cm,Q188A, top and bottom throughout. Anchoring of the floor beams on the strip foundation using bolts M12,
e < 60cm (by customer).
-
2 The wooden parts of the building kit are delivered with a residual moisture content of about 15%.
Wood "works"! This means that the wooden parts will swell during prolonged damp weather and shrink (dry out)
during prolonged dry periods. This only occurs in height or width, not lengthwise.
The block planks are firmly screwed to the vertical corner post during installation. This will not change its length,
but the horizontally attached planks change their height. If damp weather persists, the block planks can swell
slightly after completion. It is therefore important to leave 1mm clearance between the planks when fitting. Use
the enclosed spacer (to avoid unnecessary strains in the structure).
The block planks are firmly screwed to the vertical corner post during installation. This will not change its length,
but the horizontally attached planks change their height. If damp weather persists, the block planks can swell
slightly after completion. It is therefore important to leave 1mm clearance between the planks when fitting. Use
the enclosed spacer (to avoid unnecessary strains in the structure). Please remember this during the installation
of the planks, otherwise it may result in different wall heights.
-
3
If the door cannot be closed properly, this can be adjusted by turning the hinges.
-
The roofing boards are laid out up to the inner edge of the outer facing. The final roofing board must be adjusted
4
in width. The roofing boards must be cut out as necessary in the area near the fastening wood H58/58-00 (34cm).
-
5 It is planned to have the roofing paper go up the sides over the existing gap as high as the facing, and to attach it
there on the facing. The building contractor can also lay strips over the gap, or the roofing paper can be laid right
up to the upper edge of the facing; this will then be covered by the aluminium strip A100-220.
© SKAN HOLZ Europe GmbH D-21227 Bendestorf. Technical modifications reserved. All dimensions are approximate dimensions. 07/2018
610884 (unbehandelt)
610884-13 (schiefergrau)
1