Werbung
Verfügbare Sprachen
Verfügbare Sprachen
USER MANUAL
EN
Thank you for purchasing this stand, which is used to install loudspeakers with
standard mounting flange (Ø35 mm). In addition, light fixtures can be mounted
using the M10 female thread. The stand is equipped with three M20 female
threads for off-center mounting and is adjustable in height. The stand is designed
for even load distribution of up to 18 kg and intended for professional use, e.g. on
stages, in discotheques, theaters etc. Please read these operating instructions
carefully before using the product. They contain important information for the
correct use of your product. Please keep them for future reference.
FEATURES
Square base plate (55 x 55 cm)
Ÿ
3 x M20 thread for off-center installation
Ÿ
35 mm extension tube with M10 thread for light fixtures
Ÿ
Height adjustable from 136 to 240 cm, with locking pin
Ÿ
Stable steel version with carry handles
Ÿ
Centric load: 18 kg
Ÿ
Scratch-resistant black finish
Ÿ
SAFETY INSTRUCTIONS
Only use the product according to the instructions given herein. Damages due
Ÿ
to failure to follow these operating instructions will void the guarantee! We do
not assume any liability for any resulting damage.
We do not assume any liability for material and personal damage caused by
Ÿ
improper use or non-compliance with the safety instructions. In such cases,
the guarantee will be null and void.
Unauthorized rebuilds or modifications of the product are not permitted for
Ÿ
reasons of safety and render the guarantee invalid.
This product is not a toy. Keep it out of the reach of children. Do not leave
Ÿ
packaging material lying around carelessly.
Unauthorized rebuilds or modifications of the product are not permitted for
Ÿ
reasons of safety and render the guarantee invalid.
This product is intended for indoor use only. Using it outdoors could lead to
Ÿ
product failure and personal injury.
Never exceed the maximum load of the stand. In case of overload, the stand
Ÿ
may tip over and cause injuries and property damage.
There is an increased risk of tipping if the extension tube is mounted off-center
Ÿ
using the outer threads. In this case, the stand must be additionally secured
with a ballast weight or fastened. Set up a safety area around the stand.
The stand must always be set up on firm and even ground (max. inclination 5°)
Ÿ
capable of supporting the weight of both the stand and the load. When the
stand is installed on soft or uneven ground, the stand may tip over and cause
injuries and property damage.
If a loaded stand with raised column is moved, the stand may tip over and
Ÿ
cause injuries and property damage. Remove installed devices and lower the
column before moving the stand.
The installer is responsible for adhering to the carrying capacity given by the
Ÿ
manufacturer, the safety requirements and the qualification of possible co-
workers. Make sure that the installation complies with the standards and rules
that apply in your country.
After installation, this product requires inspections periodically to prevent the
Ÿ
possibility of rot, deformation and looseness.
Before taking into operation, check upon possible damages. If defective, the
Ÿ
stand must not be taken into operation.
This product is maintenance-free, except for occasional cleaning. You can use
Ÿ
a slightly dampened cloth for cleaning.
Comply with all applicable disposal laws in your country.
Ÿ
Should you have further questions, please contact your dealer.
Ÿ
Omnitronic is a brand of Steinigke Showtechnic GmbH • Andreas-Bauer-Str. 5 • 97297 Waldbüttelbrunn, Germany
BPS-3
SPEAKER/LIGHTING STAND
USE
A
Increased risk of tipping with off-center installation!
When using the outer threads B+C, fasten the stand or attach
ballast weights and set up a safety area around the stand.
Setup - Screw the stand tube into one of the threads in the base plate.
Loading - Attach the loudspeaker on the top end of the stand or fasten a light
fixture.
Height adjustment - Loosen the safety screw of the extension tube and pull it out
to the desired height. Insert the locking pin to secure the height adjustment.
Tighten the safety screw again.
Disassembly - Disassembly is effected in reverse order.
TECHNICAL SPECIFICATIONS
Item number:
60004128 (black), 60004131 (white)
Max. carrying capacity:
18 kg
Adjustable height:
136-240 cm
Tube:
Ø35 mm with M10 thread
Material:
Steel
Base plate:
55 x 55 cm
Weight:
13.5 kg
Subject to change.
www.omnitronic.de
C
B
Publ. 09/2022
Werbung
