General Description - toparc TT120 Bedienungsanleitung

An electric shock could cause serious injuries or potentially even deadly accidents.
Do not touch any live part of the machine (inside or outside) when it is plugged in because they are connected to the welding
circuit.
Do not touch the torch or and the earth clamp at the same time.
Always wear dry clothes which are in good condition in order to be isolated from the welding circuit. Always wear insulated shoes, regardless of the
environment in which you work in.
PRECAUTION FOR USE
Never wrap the welding leads around your body.
Do not use the torch to move the welding power source or wire feeder.
The torch must be fully uncoiled to prevent overheating.
Switch off the generator after the torch is cooled and before each maintenance and before replacing or control wearing parts.
Regularly check the condition of the torch. If damaged, the torch must be replaced.

GENERAL DESCRIPTION

SPECIFICATIONS
The MIG 15 / MIG 25 / MIG 36 / TT120 / PT120 torches are intended to the manual MIG / MAG welding processes.
TECHNICAL SPECIFICATIONS
Component
Part number
71846 71847
Designation
Process
(GMAW / FCAW)
Guidance method
Rated current
150 A
Corresponding
35%
duty cycle
Rated voltage
Cooling mode
Connections
150 A CO2 /
Gas protection
120 A Mix
10-18 L/min
Gas flow (2.64/4.75 US
gpm)
Ø 0.8 Ø 1.0
Contact tube
Steel Steel
Cable length
Cross section
14 mm²
Switch trigger
voltage
Functionning
temperature
Storage
temperature
Applied standard
IEC 60974-7
SET UP
TORCH CONNECTION REQUIREMENT
MIG 15 / MIG 25 / MIG 36 / TT120 / PT120
063754 063761
71848 71866
MIG 15
MIG / MAG
Manual
180 A
60%
≤113 V
Air
EURO
180 A CO2 /
150 A Mix
10-25 L/min
(2.64/6.60 US
gpm)
Ø 0.8 Ø 0.8 Ø 1.2 Ø 0.8
Steel Alu Alu Steel
3 m 3 m
16 mm²
10 V
MIG 15-25-36
The generator must be switched off.
Insert the torch connector (A) in the
female connector (E) and screw the
part B. Make sure the torch is tight
enough.
To remove the torch, unscrew as
shown below.
Component
063778
71879 C71453
MIG 25
MIG / MAG
(GMAW / FCAW)
Manual
230 A
60%
≤113 V
Air
EURO
230 A CO2 /
200 A Mix
10-25 L/min
(2.64/6.60 US gpm)
Ø 1.0 Ø 1.0 Ø 1.0
Steel Steel Steel
3 m 3 m 4 m 4 m
25 mm²
10 V
- 10  +40°C
- 10  +55°C
IEC 60974-7
063785 063792 063808
C71454
MIG 36 TT120
MIG / MAG
(GMAW / NO GAS MIG
FCAW)
Manual Manual
340 A 120 A
60% 35%
≤113 V ≤113 V
Air Air
EURO Fixed
340 A CO2 /
-
300 A Mix
10-25 L/min
(2.64/6.60 US -
gpm)
Ø 1.0 Ø 1.2 Ø 1.2 Ø 0.9
Alu Steel Alu Steel
3 m 4 m 3 m 2.5m
42 mm² 10 mm²
10 V 10 V
IEC 60974-7 IEC 60974-7
TT120 - TP120
The generator must be switched off.
1. Open the cover.
2. Unscrew the 4 screws (framed in black).
3. Disconnect the cables and remove the
torch.
4. Replace the new lamp.
5. Reconnect in the same way and then
screw it back on.
EN
Component
53277 C71391 71392
PT120
MIG/MAG
Manual
120 A
35%
≤113 V
Air
Fixed
120 A CO2 /
100 A Mix
6-15 L/min
Ø 0.8
Steel
2.35m 2.2 m 2.4m
10 mm²
10 V
IEC 60974-7
7