Technical Data; Manufacturer's Terms Of Warranty - Trumatic S 3002 Gebrauchsanweisung

Technical data

determined in accordance with EN 624 or Truma test
conditions
Trumatic S 3002 (P), S 5002
Type of gas
Liquid gas (propane / butane)
Operating pressure
30 mbar (see data plate)
Rated thermal output
S 3002 (P): 3400 W
S 5002: 5500 W
Gas consumption
S 3002 (P): 30 – 280 g/h
S 5002: 60 – 480 g/h
Operating voltage
1.5 V
Power consumption
50 mA (ignition)
0.01 mA (monitoring)
Weight
S 3002 (P): 9.8 kg (without fan)
S 5002: 17.5 kg (without fan)
S 5002 with front case with flame effect: approx. 19.5 kg
(without fan)
Front case with flame effect
Operating voltage
12 V (DC / AC)
Power consumption with sound
0.65 A (DC) / 0.91 A (AC)
Power consumption without sound
0.63 A (DC) / 0.90 A (AC)
Fuse
1.25 AT (slow)
Weight
approx. 5.2 kg
Declaration of conformity
The Trumatic S has been tested by the DVGW and complies
with the gas equipment directive (90/396/EEC) and the other
applicable EC directives. The following CE Product Ident. No.
is available for EU countries
S 3002 (P): CE-0085AP0325
S 5002: CE-0085AP0326
The heater complies with heater directive 2001/56/EC and
supplements 2004/78/EC and 2006/119/EC and bears the
type approval number
S 3002 (P): e1 00 0140
S 5002: e1 00 0141
The heater complies with the interference suppression
directive 72/245/EEC for vehicle engines with annexes
2004/104/EC, 2005/83/EC and 2006/28/EC and bears
type approval number:
e1 03 2603
The heater complies with EMC directive 2004/108/EC and low
voltage directive 2006/95/EC.
The heating system satisfies the End-of-Life Vehicle Directive
2000/53/EC.
The right to effect technical modifications is reserved!

Manufacturer's terms of warranty

1. Case of warranty
The manufacturer grants a warranty for malfunctions in the
appliance which are based on material or production faults.
In addition to this, the statutory warranty claims against the
seller remain valid.
A claim under warranty shall not pertain:
– for parts subject to wear and in cases of natural wear and
tear,
– as a result of not original Truma parts being used in the ap-
pliance and as a result of unsuitable gas pressure regulators
being used,
– as a consequence of failure to respect Truma instructions
for installation and use,
– as a consequence of improper handling,
– as a consequence of improper transport packing.
2. Scope of warranty
The warranty is valid for malfunctions as stated under item 1,
which occur within 24 months after conclusion of the pur-
chase agreement between the seller and the final consumer.
The manufacturers will make good such defects by sub-
sequent fulfilment, i.e. at their discretion either by repair
or replacement. In the event of manufacturers providing
service under warranty, the term of the warranty shall not
re commence anew with regard to the repaired or replaced
parts; rather, the old warranty period shall continue to run.
More extensive claims, in particular claims for compensatory
damages by purchasers or third parties, shall be excluded.
This does not affect the rules of the product liability law.
The manufacturer shall bear the cost of employing the Truma
customer service for the removal of a malfunction under war-
ranty – in particular transportation costs, travelling expenses,
job and material costs, as long as the service is carried out in
Germany. The warranty does not cover customer service work
in other countries.
Additional costs based on complicated removal and installa-
tion conditions of the appliance (e.g. removal of furniture or
parts of the vehicle body) do not come under warranty.
3. Raising the case of warranty
The manufacturer's address is:
Truma Gerätetechnik GmbH & Co. KG,
Wernher-von-Braun Strasse 12,
85640 Putzbrunn.
In Germany, always notify the Truma Service Centre if prob-
lems are encountered; in other countries the relevant service
partners should be contacted (see Truma Service Booklet or
www.truma.com). Any complaints are to be described in de-
tail. In addition, the properly completed guarantee certificate
is to be presented, or the factory number of the unit and the
date of purchase given.
In order for the manufacturers to be able to determine wheth-
er an incident subject to guarantee has occurred, the end user
must, at his own risk, bring the device to the manufacturers or
send it to them. If there is damage to heaters (heat exchang-
ers), the gas pressure regulator must also be sent back to the
factory.
In instances of the device being sent to the works, dispatch is
to be effected by freight transport. In cases under guarantee,
the works shall bear the transport costs or the costs of deliv-
ery and return. If the damage is deemed not to be a warranty
case, the manufacturer shall notify the customer and shall
specify repair costs which shall not be borne by the manufac-
turer; in this case, the customer shall also bear the shipping
costs.
13