Seite 1
Montage von Solarmodulen auf Flachdächern, in Gärten, an der Wand und auf dem Balkon. Der Neigungswinkel der Halterung kann zwischen 15° und 45° eingestellt werden und somit können die Solarmodule optimal zur Sonne ausgerichtet werden. Lieferumfang: HST90 / HST120 Bezeichnung HST90V / HST120V Bezeichnung Stk.
Seite 2
Lochstanzungen zum Anbringen der End- klemme aus oder überprüfen Sie den zu wählenden Abstand. Schritt 2.2 Beispiel Kurze Seite des Moduls Stanzlöcher 510mm oder 530mm H4/H6 oder H3/H5 (HST90) 660mm oder 680mm H2/H6 oder H1/H5 (HST90) 785mm H2/H7(HST90) 1050mm H2/H7 oder H1/H6 (HST120)
Seite 3
HST Halterung info@wattstunde.de Aufbauanleitung Bitte unbedingt lesen! Schritt für Schritt Anleitung ( HST90 / HST120) Schritt 4: 4.1 Bringen Sie die 4 Endklemmen (B1 oder B2) mit den mitgelieferten Befestigungselementen an den richtigen Stanzlöchern an. 4.2 Lassen Sie die Endklemmen locker, aber nicht auseinanderfallen, um genügend Platz für den star-...
Seite 4
Anbringen der Endklemme aus oder überprüfen Sie den zu wählenden Abstand. Schritt 2.2 Zum Beispiel Kurze Seite des Moduls Stanzlöcher 510mm oder 530mm H4/H6 oder H3/H5 (HST90) 660mm oder 680mm H2/H6 oder H1/H5 (HST90) 785mm H2/H7(HST90) 1050mm H2/H7 oder H1/H6 (HST120)
Seite 5
WATTSTUNDE GmbH Bessemerstraße 3 21339 Lüneburg HST Halterung info@wattstunde.de Aufbauanleitung Bitte unbedingt lesen! Schritt für Schritt Anleitung ( HST90V / HST120V) Schritt 4: (nur für die 2 von A von A-D-A) 4.1 Setzen Sie die 4 Endklemmen (B1 oder B2) auf die rich- tigen Stanzlöcher.
WATTSTUNDE GmbH Bessemerstraße 3 21339 Lüneburg HST Halterung info@wattstunde.de Aufbauanleitung Bitte unbedingt lesen! Schritt für Schritt Anleitung ( HST90V / HST120V) Schritt 7: 7.1 Passen Sie die Position der Halterung (A) an und sichern Sie die Endklemmen vollständig (zuerst die unteren zwei, dann die oberen zwei).
Seite 7
The angle of inclination of the bracket can be adjusted between 15° and 45° and thus the solar modules can be optimal- ly aligned to the sun. Included: HST90 / HST120 HST90V / HST120V Description Pcs.
Seite 8
HST bracket info@wattstunde.de Instructions Please read it! Step by step guide (HST90/HST120): Instructions for HST90V/120V can be found on page 4. Step 1: Place the triangular brackets (A) parallel and folded on the flat ground. Make sure that the distance is more than 60 % of the long side of the solar module.
Seite 9
Instructions Please read it! Step by step guide ( HST90 / HST120) Step 4: 4.1 Attach the 4 end clamps (B1 or B2) to the correct punched holes using the fasteners provided. 4.2 Leave the end clamps loose, but not falling apart, to allow enough space for the rigid frame of the solar module.
Seite 10
Step 2.2 For example Short side of the module punch holes 510mm or 530mm H4/H6 or H3/H5 (HST90) 660mm or 680mm H2/H6 or H1/H5 (HST90) 785mm H2/H7(HST90) 1050mm H2/H7 or H1/H6 (HST120)
Seite 11
WATTSTUNDE GmbH Bessemerstraße 3 21339 Lüneburg HST bracket info@wattstunde.de Instructions Please read it! Step by step guide ( HST90V / HST120V) Step 4: (only for the 2 of A von A-D-A) 4.1 Place the 4 end clamps (81 or B2) on the correct punch holes.
Seite 12
WATTSTUNDE GmbH Bessemerstraße 3 21339 Lüneburg HST bracket info@wattstunde.de Instructions Please read it! Step by step guide ( HST90V / HST120V) Step 7: 7.1 Adjust the position of the bracket (A) and fully secure the end clamps (first the bottom two, then the top two).