Go Green gtd7010341 Anleitung

Go Green Digital thermostat radiator
valve
Please read the user manual before you place the thermostat.
Keep the documents for later questions and provide them if you
pass the thermostat on to other persons.
In this packing:
• Go Green Radiator Thermostat Valve energy saving radiator
thermostat
• User manual
• Connector
• 3 Adapters
Application as directed
By purchasing the Go Green Radiator Thermostat Valve
energysaving radiator thermostat you own a program mable radiator
thermostat which can be used for temperature regulations in
enclosed rooms andtherefore, it can contribute to the reduction of
heating energy. – Please use the thermostat only for this purpose.
The programming port is intended ONLY for our programming stick.
Never connect other devices with the programming port!
Display and control elements
1) Heating times
2) Child lock active
3) Battery low
4a) Travel function
0 6 12 18 24 1
active Mo Di Mi Do Fr Sa So
2
4b) Comfort temperature
:
3
active
4c) Economy temperature
4
AUTO
MANU
active
5
4d) Window/freeze
6
protection function active
5) AUTO or MANU mode
active
6a) Button – leads to
MENU
7
the main menu (starting
from regular display);
within the menu one
keypress leads to the
previous level
6b) Button - confirmation of setting
OK
6c) Button - timer function
7) Selector wheel
Set up menu
By pressing you will arrive at the set up menu.
MENU
Please choose one of the items with the selector wheel.
With OK you can select one menu item and with the selection
wheel they can be adjusted. The button confirms the setting.
OK
The button leads to the previous level.
MENU
MODE to select the mode
AUTO = automatic mode
MANU = manual mode
PROG setting of time programme
TEMP setting of comfort and economy temperature
ZEIT setting of date and time
FENS window function
RES reset of the device to factory preset
ADAP starting of a new adaptation to adjust the valve
URLA travel function
INST installation function
OFFS adaptation of temperature to the room situation
Inserting / replacing batteries
In order to open the battery compartment please push at the
marked positions to remove the cover.
Then insert the batteries as shown in the illustration.
Do not use accumulators! Ensure that the polarity is correct!
Attention:
• Never recharge batteries, danger of explosion!
• Do not short-circuit batteries!
• Do not disassemble batteries!
• Take low batteries out of the device immediately.
• Keep batteries away from extreme warming – danger of leakage!
• Do not apply used and new batteries together.
• If needed, clean the battery and the contacts before using them.
• Keep the batteries away from children.
• When getting in touch with battery acid instantly irrigate the
affected parts with clear water and call a doctor.
Setting date and time
After inserting the batteries for the first time, the date will flash on
the display. Now, date and time can be set.
Set date with the selector wheel.
Confirm with
OK
Set month with the selector wheel.
Confirm with
OK
Set day with the selector wheel
Confirm with
OK
Set hour with the selector wheel
Confirm with
OK
Set minute with the selector wheel
Confirm with That's it
OK
On the display will be shown. Now, the motor will completely
move to the installation position in order to make the installation easier.
As soon as Go Green Radiator Thermostat Valve is ready for
installation will be shown on the display.
You can also set date and time via the menu item later on.
But in case of that, Go Green Radiator Thermostat Valve does not
move to the installation position.
→ In case of replacing batteries, the stored time programme will
remain active. You should check the specified time to ensure that.
Installation
Go Green Radiator Thermostat Valve can be quickly and easily
mounted on all common valves (see adapter table). It can be installed
without grime and water spots because the heating circuit is not
interrupted.
1) Turn the manual thermostat head up completely, loosen the
fastening and pull the thermostat off of the valve.
2) Use an appropriate adapter, if required, and push it onto the valve.
Screw the connector on the valve or the adapter.
Now, you put Go Green Radiator Thermostat Valve on the
connector until it noticeably clicks into place.
→ In case of a later installation , please switch in the menu to
before you install the device. Herewith the installation is
facilitated.
Dismounting
→ In order to dismount Go Green Radiator Thermostat Valve press
the releasing device to loosen the locking device. Now, pull the
Go Green Radiator Thermostat Valve off of the valve.
Adaptation
Initial installation: Press the button OK until appears on the
display so that Go Green Radiator Thermostat Valve will be able to
start its adaptation. The device will adapt itself to the stroke of your
valve body. To do this the valve will now be opened and closed
several times to store the end points.
In some cases this process can take a few minutes.
After successful adaptation it returns to normal mode.
→ Should adaptation become necessary again, e.g. if your radiator
does not cool down in the -Position, please press in the
menu the button until adaptation starts again.
→ If the mistake is shown on the display place Go Green Radiator
Thermostat Valve onto the radiator valve and then take the
batteries out for a short time in order to execute a reset.
Basic operating modes
MANU-mode
In the MANU-mode Go Green Radiator Thermostat Valve adjusts to
the manually specified temperature.
AUTO-mode
In the AUTO-mode Go Green Radiator Thermostat Valve changes
between to temperatures according to the time programme that has
been set:
comfort temperature (factory preset 21°C)
economy temperature (factory preset 16°C)
The heating and economy times can be specified via the adjustable
time programme. It is possible to set 8 switch points (4 heating and
4 economy times) per day at the most. Go Green Radiator
Thermostat Valve the following factory preset:
Heating time:
Heating with comfort temperature (factory preset: First heating
time at 07:00)
Economy time:
Lowering to economy temperature (factory preset: First economy
time at 22:00)
Setting heating and economy times
With Go Green Radiator Thermostat Valve it is possible to set
4 heating and 4 economy times per day – one for each day or one
for a block of several days.
TAG1 to TAG7 represent the weekdays from Monday to Sunday.
Additionally, the corresponding days are shown as abbreviation below
the menu bar on the display.
Block construction:
T1–5 = same programme from Monday to Friday
T1–6 = same programme from Monday to Saturday
T1–7 = same programme from Monday to Sunday
→ For non-programmed days the factory preset remains active.
Setting of an individual programme
Press . Select the menu item with the selector wheel.
MENU
Press OK
for Monday is shown on the display.
Select day/block with the selector wheel. Confirm with OK
Set the beginning of the first heating time (symbol ) with the selector
wheel. Confirm with
OK
Set the beginning of the first economy time (symbol ) with the
selector wheel. Confirm with
OK
Now, if desired, a second, third or fourth heating/economy time can
be entered.
→ If you do not want to set a further heating/economy time confirm
"-- --" with
OK
The next day for programming is shown on the display.
→ If you do not want to enter a further day, leave the menu with
. If the temperature is shown on the display the programming
MENU
is finished.
→ Within the blocks you can also overwrite single days with different
times.
Setting comfort and economy temperature
Press . Select the menu item with the selector wheel .
MENU
Confirm with .
OK
Set comfort temperature with the selector wheel. Confirm with
OK
Set the economy temperature with the selector wheel.
Confirm with
OK
Area 8°C, freeze protection function is active
Area valve is completely open
Remark
Maximum energy saving can be obtained with an economy
temperature which is about 5˚C below the comfort temperature.
Manual operation
With the selector wheel an adaptation of the room temperature is
possible at any time. In the AUTO-mode it remains active until the
next switch point is reached. Now, the usual programme
becomes active again.
Further functions
The timer function is selected with the timer-button
With this function a user-defined temperature for a programmable
period can be entered. This can be very useful in case of a party,
for example. Press . First, the time for which the time
programme has been deactivated is shown. Confirm with .
OK
Now, the desired temperature can be set. Confirm with
OK
Offset
If the perceived temperature significantly differs from the set
thermostat temperature a temperature set up can be executed.
Press . Select the menu item with the selector wheel.
MENU
Confirm with . The degree setting will flash on the
OK
display.
Now set up the desired adaptation for the temperature (from -5 up
to 5ºC) with the selector wheel. Confirm your entry with
OK
The temperature display does not change !
Window function
If you open a window and consequently the temperature drops
significantly Go Green Radiator Thermostat Valve will automatically
close the heating valve in order to save energy. The display will
show . Afterwards Go Green Radiator Thermostat Valve will
resume normal operation.
For the set up select in the menu. Confirm with
OK
First, the sensibility is selected with the selector wheel
= high sensibility
= medum sensibility (factory preset)
= low sensibility). Confirm with
OK
Now, you enter the time (10min (factory preset) - 60 min)
for which the valve should remain closed. Confirm with
OK
Travel function
For the time you are absent you can select an individual temperature.
After this period the originally defined programme becomes active
again.
Press . Select the menu item . Confirm with
MENU OK
(Suitcase symbol appears on the display)
Select with the selector wheel the end of the travel function
(= date of the recommencement of the regular heating times).
Confirm with
OK
Set the time and confirm with the button
OK
The signal appears on the display. Now set the temperature
and confirm with . (Suitcase symbol appears on the
OK
display). With MENU the function can be activated.
Child lock
You can lock Go Green Radiator Thermostat Valve to protect the
device from unauthorized activation.
Press the buttons OK and at the same time for about
2 seconds until the symbol appears on the display in order to
lock the device. By using this button combination again the symbol
disappears and you release the lock.
Heating pause – Closing the Go Green Radiator Thermostat Valve
Press . Select the menu item with the selector wheel.
MENU
Confirm with
OK
Select and confirm with .
OK
Set the temperature on the display to .
The valve is now closed and will work with a time programme.
The calcification protection function remains active once a week.
After the heating pause you switch in the menu to the AUTO-mode
and the personally set programme will be executed again.
Going back to factory preset / All reset
Press . Select the menu item with the selector wheel.
MENU
Confirm with . flashes, confirm with
OK OK
Go Green Radiator Thermostat Valve is reset again.
Now proceed as described for the initial operation.
Freeze protection and calcification protection function are active
automatically
Freeze protection function
If the temperature drops below 6°C, Go Green Radiator Thermostat
Valve opens the valve until the temperature again rises above 8°C.
This prevents the radiators from freezing.
Calcification protection
To prevent radiator valves from calcifying Go Green Radiator
Thermostat Valve is submitted to a calcification protection programme
once a week on Friday mornings.
Cleaning and used devices
Cleaning
To clean the Go Green Radiator Thermostat Valve use only a
dry or lightly wet cloth. Avoid chemical solvent – it can probably
damage the device.
Used devices
Do not throw old devices and packaging into the household waste.
They can be recycled. You receive further information at your
local government.
Adapters
Heimeier, Junkers Landys+Gyr,
no adapter required
MNG, Honeywell, Braukmann,
thread-measure dimension of
M 30x1,5
Danfoss RAV (accompanying pin
must be plugged on the valve
tapped)
+ accompanying pin,
only for RAV!
Danfoss RA
Danfoss RAVL
Help
Problem Cause Solution
Replace batteries.
Batteries do not
have enough power.
Adapt again (see
Heating element Valve does not
Adapting).
does not cool close completely.
down Move the valve
It may be that the
closing point of
stem several times
your valve seat by hand, it may be
has shifted that adaptation is
impossible because
your valve is
calcified or the
seat no longer
performs its function
Heating element Is the boiler water Adjust the water
does not warm temperature OK ?
temperature of the
boiler water
up
Valve does not
Remove the Go
open, is it calcified
Green Radiator
after the summer
pause/ heating Thermostat Valve,
pause ?
move the valve stem
back and forth per
hand or with a tool
No adaptation
Is the installation
OK?
possible
Go Green Radiator
Install the product
Thermostat Valve
to the heater. '
Open and close the
not installed to the
heater valve several times
Valve stroke is too
manually or
short replace the batteries
Motor movement Does the valve
is not possible stem move
freely ?
www.go-green.nl
Art.nr. gtd7010341