Noise Information; Items Included - Bosch GTS 254 Professional Originalbetriebsanleitung

Table saw
Weight according to EPTA-
Procedure 01:2014
Protection class
Dimensions (including detachable parts of the tool)
Width x depth x height
Dimensions of suitable saw blades
Saw blade diameter
Base blade thickness
Min. tooth thickness/offset
Hole diameter
Maximum workpiece dimensions: (see "Maximum workpiece dimen-
sions", page 35)
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.

Noise information

Noise emission values determined according to
EN 62841-3-1.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 90 dB(A); sound power level
105 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
The noise emission value given in these instructions has
been measured in accordance with a standardised measur-
ing procedure and may be used to compare power tools. It
may also be used for a preliminary estimation of noise emis-
sions.
The noise emission value given represents the main applica-
tions of the power tool. However, if the power tool is used
for other applications, with different application tools or is
poorly maintained, the noise emission value may differ. This
may significantly increase noise emissions over the total
working period.
To estimate noise emissions accurately, the times when the
tool is switched off, or when it is running but not actually be-
ing used, should also be taken into account. This may signi-
ficantly reduce noise emissions over the total working
period.
Assembly
Avoid starting the power tool unintentionally. The
u
mains plug must not be connected to the power supply
during assembly or when carrying out any kind of
work on the power tool.

Items included

Check to ensure that all the parts listed below have been
supplied before using the power tool for the first time:
– Table saw with mounted saw blade (28)
– "Power tool" fastening set (39) (8 fastening screws, 8
washers)
Bosch Power Tools
– Base unit (14)
GTS 254
– "Base unit" fastening set (37) (16 fastening screws, 16
kg 24.4
washers, 16 securing rings, 16 nuts)
– Tilt protector (13)
/ II
– "Tilt protector" fastening set (38) (4 fastening screws, 8
washers, 4 securing rings, 4 nuts)
mm 690 x 620 x 100
– Angle guide (3)
0
– Profile rail (50)
– "Profile rail" wing nut (51)
mm 254
– Parallel guide (9)
mm < 1.8
– Additional parallel guide (47)
mm > 2.4 – "Additional parallel guide" fastening set (48) (2 fastening
screws, 2 wing nuts)
mm 30
– Riving knife (27) with protective cover (6) fitted
– Anti-kickback pawls (7)
– Ring spanner (35)
– Hook spanner/open-ended spanner (36)
– Push stick (15)
– Table insert (8)
Note: Check the power tool for possible damage.
Before continuing to use the power tool, carefully check that
all protective devices or slightly damaged parts are working
perfectly and according to specifications. Check that the
moving parts are working perfectly and without jamming;
check whether any parts are damaged. All parts must be fit-
ted correctly and all the conditions necessary to ensure
smooth operation must be met.
If the protective devices or any parts become damaged, you
must have them properly repaired or replaced by an author-
ised service centre.
Stationary or flexible mounting
To ensure safe handling, the power tool must be
u
mounted on a flat, stable work surface (e.g. work
bench) before use.
Assembly with base unit and tilt protector
(see figures a1−a3)
For assembly, use the "base unit" (37), "tilt protector" (38)
and "power tool" (39) fastening sets
– Screw the base unit (14) together. Tighten the screws
firmly.
– Screw the tilt protector (13) to the base unit.
– Place the power tool on the base unit so that the tilt pro-
tector points to the rear.
– Attach the power tool to the base unit. For this, use the
lateral holes (31) of the power tool as well as the holes in
the base unit.
Assembly without base unit (see figure b)
– Use a suitable screwed connection to secure the power
tool to the work surface. The holes (32) are used for this
purpose.
English | 31
1 609 92A 72F | (13.10.2021)