Bosch GTA 3800 Professional Originalbetriebsanleitung Seite 17

No. Designation
GTA 3800 saw stand
(4) Holder set
(1) Workpiece support
(7) Roller support
(14) Socket spanner (13 mm)/hex key
(4 mm)/cross-headed screwdriver
(19) Power tool fastening set consists of:
– Hexagon screw (M8 x 45)
– Washer
Extra tools required (not included in the delivery):
– Open-end spanner (10 mm)
Installing the Saw Stand
Carefully remove all parts included in the delivery from their
packaging.
Remove all packing material.
Setting up the saw stand (see figures A1−A2)
– Place the saw stand on the floor with legs up.
– Press the locking pin (15) in and swivel the leg up until
the locking pin audibly engages again.
– Repeat this work step with the other three legs.
– Rotate the saw stand into the working position.
– Make sure that the saw stand is stable and all locking pins
have engaged.
– A height-adjustable foot (9) helps you to align the saw
stand.
– Screw the foot in or out until the saw stand is level and all
four legs are on the ground.
Installing roller support (see figure B1)
– Unscrew the cross-head screw of the roller support (7)
with the supplied cross-headed screwdriver (14).
If required, resist the lock nut on the other side of the
roller support with an open-end spanner (10 mm).
– Remove the roller support (7).
There are various options as to how the individual rollers can
be arranged on the workpiece support using the internal
threaded rod.
– Arrange the individual parts as required and push the in-
ternal threaded rod through the rollers and through the
workpiece support (1).
– Screw all parts back together.
Installing workpiece support (see figure B2)
– Release the locking knobs (3) and pull the table
extensions (2) slightly out on both sides of the saw stand.
– Push the workpiece supports (1) from left and right re-
spectively into the upper groove of the saw stand or the
table extension.
– The length stops (8) must point outwards here.
– Pull the locking knob (6) to lock the workpiece support.
Bosch Power Tools
Preparing the Saw Stand
Quantity
1
Preparing holder sets (see figures C1–C4)
2 – To unlock the holder sets (4), press the buttons (16) and
open the levers (17) respectively.
2
– Measure the distance x between the assembly holes on
2
your power tool.
1
– Position the holder sets (4) in the centre of the saw stand
and at the appropriate distance x from each other.
– Close each lever (17) again. This allows the holder sets to
4
be firmly positioned on the saw stand.
4
Setting up the saw stand (see figure D)
– Bring the power tool into the transport position. Informa-
tion about the transport position can be found in the op-
erating instructions for the corresponding power tool.
– Position the movable nuts (18) in the holder sets so that
they match the assembly holes on the power tool.
– Screw using the supplied socket spanner (14) holder set
and power tool with the hexagon screws and washers
from the fastening set (19).
Operation
Working Advice
Always hold the workpiece firmly in place, especially long,
heavy pieces. Once the workpiece has been cut, the centre
of gravity may be displaced, causing the saw stand to tip
over.
Do not overload the saw stand. Always observe the max-
imum load bearing capacity of the saw stand.
Preparing the workpiece support
The free end of long workpieces must have something
placed underneath it or be supported.
Adjusting the height of the workpiece support
(see figure E)
– Place your workpiece on the saw table for the power tool.
– Release the locking knob (5) and adjust the height of the
roller support (7) so that your workpiece is straight.
– Re-tighten this locking knob.
Sawing workpieces of the same length (see figure F)
The length stop (8) can be used for easily sawing workpieces
of the same length.
– Pull the length stop (8) up until it engages.
– Position the workpiece support (1) at the required dis-
tance from the saw blade of the power tool.
– To insert the length stop (8), tilt the length stop in and
press it fully down.
Extending the saw stand (see figure G)
The saw stand can be extended on both sides.
– To stabilise the saw stand when machining long and
heavy workpieces, you can support the table
extension (2) with a support leg (13).
English | 17
1 609 92A 6JA | (13.04.2021)