Abkürzungen verwendet. Zum besseren Verständnis sind diese in den folgenden Abschnitten erklärt. 1.3.1 Sicherheitshinweise In dieser Dokumentation stehen Sicherheitshinweise im Kapitel 2.6 „Produktabhängige Sicherheitshinweise“ und Kapitel 3 „Allgemeine Hinweise zu 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Bedeutung Wenn diese Information nicht beachtet wird, kann das Produkt nicht optimal genutzt bzw. betrieben werden. Einzelner, unabhängiger Handlungsschritt Nummerierte Handlungsanweisung: Die Ziffern geben an, dass die Handlungsschritte aufeinander folgen. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Benutzer. Ebenfalls nicht bestimmungsgemäß sind folgende vorhersehbare Fehlanwendungen: • Der Transport von anderen als den spezifi zierten Transportgütern. • Das Mitfahren von Personen auf dem Produkt oder dem Transportgut. 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Produkt nur dann in sicherheitsrelevanten Anwendungen ein, wenn diese Verwendung ausdrücklich in der Dokumentation des Produkts spezifi ziert und erlaubt ist, beispielsweise in Ex-Schutz-Bereichen oder in sicherheitsbezogenen Teilen einer Steuerung (funktionale Sicherheit). Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
– die Zugänge zu NOT-HALT-Befehlsgeräten frei von Hindernissen sind. – alle Aufgabestellen, Arbeitsplätze und Durchgänge freigehalten werden. • Verwenden Sie die NOT-HALT-Befehlsgeräte nicht für das normale Anhalten. • Überprüfen Sie regelmäßig die ordnungsgemäße Funktion der NOT-HALT- Befehlsgeräte. 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• Stellen Sie vor der erstmaligen Inbetriebnahme sicher, dass keine hervorstehenden oder scharfkantige Teile das Personal im Arbeits- oder Verkehrsbereich gefährden. • Führen Sie vor der erstmaligen Inbetriebnahme oder Wiederinbetriebnahme und dann regelmäßig eine Sicherheitstechnische Unterweisung des Betriebspersonals durch. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Produkt ausschließlich mit einem leicht feuchten Tuch aus nicht faserndem Gewebe. Verwenden Sie dazu ausschließlich Wasser und bei Bedarf ein mildes Reinigungsmittel. • Verwenden Sie zur Reinigung keine Hochdruckreiniger. 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Verwendung Positioniereinheit PE 2 • Einbau in Bandstrecke BS 2… • Abheben vom Fördermittel und positionieren von Werkstückträgern WT 2 in einer manuellen/automatischen Bearbeitungsstation mit hohen Anforderungen an die Positioniergenauigkeit (±0,1 mm). Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
• Zulässige vertikale Prozesskraft bei mittiger Beladung: bis zu 300 N incl. WT 2. 5.2 Produktbeschreibung Hubplatte Zentrierdorne Schutzkasten Höhenausgleich Anzeige der Einbau- richtung der PE 2 358 722-01 Abb. 2: Positioniereinheit PE 2 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• Setzen Sie das Produkt nur auf ebener Fläche ab. • Schützen Sie das Produkt vor mechanischen Einwirkungen. • Schützen Sie das Produkt vor Umwelteinfl üssen, wie Schmutz und Feuchtigkeit. • Beachten Sie die Umgebungsbedingungen, siehe Seite 30. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Hammerkopfes in der Nut. Die Kerbe im Schraubenende zeigt die Orientierung des Hammerkopfes an. 1 = Einsetzlage der Hammerschraube in die Nut. 2 = Klemmlage der Hammerschraube in der Nut. Maximales Anzugsdrehmoment: 25 Nm. 7.3 Notwendiges Werkzeug • Sechskantschrauben-Schlüssel (Gabelschlüssel) SW13. 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Handlungsanweisungen des begleitenden Textes. Bezeichnung von Bauteilen in Grafi ken. Die Buchstaben kennzeichnen die im begleitenden Text erwähnten Bauteile. Detailansicht aus einer anderen Blickrichtung, zum Beispiel auf die Rückseite oder Unterseite des Produkts. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Ausrichten bis alle Schrauben festgezogen sind. Montieren Sie die PE 2. SW13 = 25 Nm ST 2/B ST 2/B-100 M8x40 M8x25 358 722-03 Abb. 4: Positioniereinheit PE 2 montieren 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Betriebsdruck: 4 bis 6 bar. Siehe Seite 31. Schließen Sie die PE 2 an die G 1/8" Druckluftversorgung an. G 1/8" 358 722-05 Abb. 5: Pneumatikplan ) nicht im Lieferumfang Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Vereinzeler VE 2/… in der Nut der Strecke gegen die Anschlagkante des Werk- stück trägers. Ziehen Sie die Schrauben des Vereinzelers fest. 358 722-04 Abb. 6: Vereinzeler VE 2/… montieren 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Einwirkmöglichkeit anderer Schaltorgane besteht. • Nehmen Sie das Produkt nur in Betrieb, wenn alle Sicherheits einrichtungen der Anlage installiert und funktionsbereit sind. • Nehmen Sie nur ein vollständig installiertes Produkt in Betrieb. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Fördermittel Kleiderstücken oder Ausreißen von und stehendem langen Haaren Haaren. Werkstück träger Fördermittel: Zwischen Einklemmen von Quetschung. Fördermittel und Körperteilen beim Werkstück träger. Absenken. 358 722-11 358 722-12 358 722-13 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• Wählen Sie die Geschwindigkeit der Förderstrecke nicht höher als für die jeweilige Funktion erforderlich. • Besonders wichtig: vermeiden Sie Verschmutzen durch abrasive Medien, reduzieren Sie das Verschmutzen durch regelmäßige Reinigung. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
– Medien mit Schmierwirkung können, wenn sie auf Systemen mit Rollen verschleppt werden, zur Reduzierung der über Reibung übertragbaren Antriebsleistung führen. In solchen Fällen ist bei der Planung der Anlage besondere Aufmerksamkeit erforderlich und die Wartungsintervalle sind entsprechend zu verkürzen. 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Sicherheitseinrichtung aufheben. • Probeläufe bei geöffneten Verkleidungen sind nur dann zulässig, wenn sie von einer sachkundigen Person unter Benutzung von Tipp-Schaltern durchgeführt werden und keine Einwirkmöglichkeit anderer Schaltorgane besteht. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Instandhaltung und Instandsetzung 10.4.1 Hubeinheit wechseln Demontieren Sie die Hubplatte. Demontieren Sie die = 8 Nm Hubeinheit. Wechseln Sie die verschlissenen Teile der Hubeinheit aus. 358 722-22 Abb. 7: Hubeinheit wechseln (1/2) Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Instandhaltung und Instandsetzung 27/32 10.4.2 Zentrierstifte wechseln Demontieren Sie die Hubplatte. Demontieren Sie die Zentrierstifte (auspressen). Montieren Sie die neuen Zentrierstifte (einpressen). 358 722-21 Abb. 8: Hubeinheit wechseln (2/2) 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Kontrollieren Sie vor dem Anheben des Produktes, ob die Tragegurte richtig befestigt sind! Sichern Sie das Produkt beim Anheben gegen Umkippen! Achten Sie während des Hebens und Senkens darauf, dass sich außer dem Bediener keine weiteren Personen im Gefahrenbereich aufhalten! Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
14 Erweiterung und Umbau • Sie dürfen das Produkt nicht umbauen. • Die Gewährleistung von Bosch Rexroth gilt nur für die ausgelieferte Konfi guration und Erweiterungen, die bei der Konfi guration berücksichtigt wurden. Nach einem Umbau oder einer Erweiterung, die über die hier beschriebenen Umbauten bzw.
Prüföl, legierte Öle, aggressive Waschsubstanzen, Lösungsmittel oder Bremsfl üssigkeit empfehlen wir die Rücksprache mit Ihrer Rexroth- Fachvertretung. • Längerer Kontakt mit stark sauer oder basisch reagierenden Stoffen muss vermieden werden. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Seite 35
Contents 3/32 Contents About This Documentation Scope of documentation Required and supplementary documentation Presentation of information 1.3.1 Safety instructions 1.3.2 Symbols 1.3.3 Designations Notes on Safety About this chapter Intended use Improper use Personnel qualifi cations General safety instructions Product-specifi c safety instructions Personal protective equipment Obligations of the system owner General Notes on Equipment and Product Damage...
Seite 36
Exchanging the centering bolts 10.5 Spare parts Decommissioning Disassembly and Exchange 12.1 Preparing the product for storage/further use Disposal Extension and Conversion Troubleshooting and Resolution Technical Data 16.1 Ambient conditions 16.2 Pneumatics Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Uniform safety instructions, symbols, terms, and abbreviations have been used in this documentation in order to ensure that you can get to work quickly and safely with your product. They are discussed in more detail in the following sections. 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Table 3: Meaning of the symbols Symbol Meaning If this information is disregarded, the operating procedure may be impaired. Individual, independent action Numbered steps: The numbers indicate the order for the steps. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Any use other than described in section “Intended use” is considered improper and is not permitted. Bosch Rexroth AG is not liable for any damages resulting from improper use. The user alone bears the risks of improper use of the product.
• Having knowledge of the function and structure of pneumatic components. Bosch Rexroth offers training for special fi elds. You can fi nd an overview of the training contents on the Internet at http://www.boschrexroth.de/didactic 2.5 General safety instructions •...
• After an EMERGENCY STOP or a malfunction, only switch on the system once the EMERGENCY STOPS, malfunctions cause of the fault has been determined and the error resolved. 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• Provide safety-related instructions to the operating personnel before fi rst use or re-commissioning, and then in regular intervals. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
• Never use solvents or aggressive detergents. Only clean the product using a slightly damp, lint-free cloth. Only use water to do this and, if necessary, a mild detergent. • Do not use a high-pressure cleaner for cleaning. 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• Assembly in belt section BS 2... • Lifting of conveyor media and positioning of WT 2 workpiece pallets in a manual or automated processing station with high demands on positioning accuracy (±0.1 mm). Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
• Permissible vertical process force with center load: up to 300 N incl. WT 2. 5.2 Product description Lift plate Centering mandrel Housing element Height compensation Mounting orientation for the PE 2 358 722-01 Fig. 2: PE 2 positioning unit 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• Only store the product on a fl at surface. • Protect the product against mechanical infl uences. • Protect the product against environmental infl uences such as contamination and humidity. • Observe the ambient conditions, see page 30. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
The notch at the end of the bolt indicates the T-bolt orientation. 1 = T-bolt insertion orientation in the slot. 2 = T-bolt clamping position in the slot. Maximum tightening torque: 25 Nm. 7.3 Required tools • Hexagon wrench (open-end) WS13. 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Designation of components in graphics. The letters identify the components specifi ed in the accompanying text. Detail view from a different direction, for example, on the back or bottom of the product. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Assemble the PE 2. SW13 = 25 Nm ST 2/B ST 2/B-100 M8x40 M8x25 358 722-03 Fig. 4: Assembling the PE 2 positioning unit 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Operating pressure: 4 to 6 bar. See page 31. Connect the PE 2 to the compressed air supply. G 1/8" G 1/8" 358 722-05 Fig. 5: Pneumatics diagram ) Not included in scope of delivery Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
VE 2/… stop gate in the groove of the section against the reference edge of the workpiece pallet. Tighten the screws of the stop gate. 358 722-04 Fig. 6: Assembling the VE 2/… stop gate. 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• Only commission the product if all safety devices have been installed in the system and are functional. • Commission the product only if it is installed completely. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Conveyor medium: Catching of body parts Crushing Between conveyor during lowering. medium and workpiece pallet. 358 722-11 358 722-12 358 722-13 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• Switch off conveyor sections when the system is not running, e.g. during breaks, over night, on the weekend. • Only select speeds that correspond with the particular function. • Especially important: Avoid contamination by abrasive media; reduce contamination through regular cleaning. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
– Media with lubricating properties may reduce the driving power that is caused by friction if they are carried over onto systems with rollers. Such cases require special attention when planning the system and the maintenance intervals need to be shortened accordingly. 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• Test runs with open housings are only permitted when they are performed by skilled workers using hold-to-run controls and when the infl uence of all other switching devices can be excluded. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Exchanging the lift unit Disassemble the lift plate. Disassemble the lift unit. = 8 Nm Exchange the worn parts on the lift unit. 358 722-22 Fig. 7: Exchanging the lift unit (1/2) Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Exchanging the centering bolts Disassemble the lift plate. Disassemble the centering bolts (pressing out). Assemble the new centering bolts (pressing in). 358 722-21 Fig. 8: Exchanging the lift unit (2/2) 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Before lifting the product, make sure that the carrying straps are correctly fastened! Secure the product to prevent toppling while lifting! Make sure that no one is in the danger area when raising and lowering, with the exception of the operator! Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
14 Extension and Conversion • Do not convert the product. • The Bosch Rexroth warranty only applies to the delivered confi guration and extensions taken into account in the confi guration. The manufacturer can accept no warranty claims if the system is converted or extended in a manner not listed in these instructions.
Contact your Rexroth representative if you have any doubts about resistance to specifi c chemicals, such as test oil, doped oils, aggressive detergents, solvents, or brake fl uid. • Avoid long-term contact with acidic or basic reacting materials. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
• Humidity – water content – Pressure dew point ≤ +3°C ) The pressure dew point should be at least 15°C below the ambient temperature. • Oil content – Oil quantity ≤ 1 mg/m 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Seite 64
Bosch Rexroth AG Postfach 30 02 07 D-70442 Stuttgart Germany Fax +49 711 811–7777 info@boschrexroth.de www.boschrexroth.com Subject to changes. 3 842 358 722/2015-05...
Seite 67
Montage du produit 1.1.4 Montage de l’unité de positionnement PE 2 1.1.5 Raccordement pneumatique du produit 1.1.6 Montage du séparateur VE 2/… Mise en service Première mise en service Risques résiduels 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Seite 68
Mise hors service Démontage et remplacement 12.1 Préparation du produit au stockage / au recyclage Elimination Elargissement et transformation Recherche et résolution des défauts Données techniques 16.1 Conditions environnantes 16.2 Pneumatique Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Afi n de travailler de manière sûre et rapide avec votre produit grâce à la présente documentation, des consignes de sécurité, symboles, notions et abréviations uniformes ont été utilisés. Afi n de faciliter la compréhension, ceux-ci sont explicités dans les paragraphes suivants. 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Si cette information n’est pas prise en compte, le produit ne peut être utilisé ou exploité de manière optimale. Action isolée et indépendante Enumération d’actions. Les chiffres indiquent la séquence des étapes de manipulation. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Toute autre utilisation que celle décrite dans le paragraphe « Utilisation conforme » n’est pas conforme et n’est par conséquent pas admise. Bosch Rexroth AG décline toute responsabilité en cas de dommages résultant d’une utilisation non conforme. Toute utilisation non conforme est aux risques et périls de l’utilisateur.
• Disposer de connaissances quant au fonctionnement et à la structure de composants pneumatiques. Bosch Rexroth vous offre des mesures qui soutiennent la formation dans des domaines spécialisés. Vous trouverez un aperçu des contenus des formations sur Internet à l’adresse http://www.boschrexroth.de/didactic 2.5 Consignes générales de sécurité...
• Assurez-vous que seul le personnel autorisé dans le cadre d’une utilisation conforme du produit – démarre et commande l’installation ou intervienne dans le fonctionnement normal. – manipule les dispositifs de réglage des composants et éléments de construction. 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• Avant la première mise en service ou remise en service, et ensuite régulièrement, procédez à une formation du personnel d‘exploitation à la sécurité. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
à l’aide d’un chiffon légèrement humide dont le tissu ne s’effi loche pas. A cet effet, servez-vous uniquement d’eau et, au besoin, d’un détergent doux. • N’utilisez pas de nettoyeur haute pression pour le nettoyage. 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• Pose dans section à bande BS 2... • Soulèvement du convoyeur et positionnement des palettes porte-pièces WT 2 dans un poste de travail manuel / automatique avec exigences élevées concernant la précision de positionnement (±0,1 mm). Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
B : Mandrins de centrage C : Carter D : Compensation de hauteur E : Indication du sens de montage de la PE 2 358 722-01 Fig. 2 : Unité de positionnement PE 2 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• Déposez toujours le produit sur une surface plane. • Protégez le produit des effets mécaniques. • Protégez le produit des infl uences ambiantes, telles que la poussière et l’humidité. • Observez les conditions ambiantes, voir page 30. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
2 = Position de serrage de la vis à tête rectangulaire dans la rainure. Couple de serrage maximal : 25 Nm. 7.3 Outils nécessaires • Clé hexagonale (clé à fourche) de 13. 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Ces lettres permettent d’identifi er les composants mentionnés dans le texte correspondant. Vue détaillée à partir d'un autre axe visuel, par exemple depuis la face arrière ou inférieure du produit. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Montez la PE 2. SW13 = 25 Nm ST 2/B ST 2/B-100 M8x40 M8x25 358 722-03 Fig. 4 : Montage de l’unité de positionnement PE 2 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Pression de service : 4 à 6 bar. Voir page 31. Raccordez la PE 2 et l’alimentation en air G 1/8" comprimé. G 1/8" 358 722-05 Fig. 5 : Schéma pneumatique ) Non compris dans la fourniture Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
• Ne mettez le produit en service que lorsque tous les dispositifs de sécurité de l’installation sont installés et opérationnels. • Ne mettez le produit en service que s’il est complètement installé. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
à l’arrêt. Convoyeur : entre le Coincement de parties Ecrasement. convoyeur et la palette corporelles lors de porte-pièces. l’abaissement. 358 722-11 358 722-12 358 722-13 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• Ne choisissez pas une vitesse de section de transport plus élevée que nécessaire pour la fonction correspondante. • Particulièrement important : évitez l’encrassement par des substances abrasives ou réduisez-le en nettoyant régulièrement. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
à rouleaux, provoquer une réduction de la puissance d’entraînement transmise par frottement. Dans de tels cas, une attention particulière est nécessaire lors de la planifi cation de l’installation et les intervalles de maintenance doivent être raccourcis en conséquence. 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• Les essais avec revêtements ouverts sont uniquement autorisés lorsqu’ils sont effectués par un spécialiste utilisant des interrupteurs à impulsion et qu’il n’existe aucune possibilité d’infl uence d’autres organes de commutation. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
10 (2x), 13 et 19. • Clés pour vis à six pans creux, ouvertures de clé 3, 4 et 5. • Tournevis cruciforme PZ2 • Pied à coulisse, 500 mm • Marteau • Pointeau 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Démontez la plaque de levage. Démontez l’unité de = 8 Nm levée. Remplacez les pièces usées de l’unité de levée. 358 722-22 Fig. 7 : Changement de l’unité de levée (1/2) Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Changement des tiges de centrage Démontez la plaque de levage. Démontez les tiges de centrage (extraire). Montez les nouvelles tiges de centrage (presser). 358 722-21 Fig. 8 : Changement de l’unité de levée (2/2) 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Durant le soulèvement, protégez le produit de tout basculement ! Durant le soulèvement et l’abaissement, veillez à ce qu’aucune autre personne que l’opérateur ne se trouve dans la zone à risque ! Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
14 Elargissement et transformation • Il est interdit de transformer le produit. • La garantie de Bosch Rexroth s’applique exclusivement à la confi guration fournie et aux élargissements dont il a été tenu compte lors de la confi guration. La garantie perd toute validité...
Bosch Rexroth. • Un contact prolongé avec des substances à forte réaction acide ou basique doit être évité. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
≤ +3 °C ) Le point de rosée sous pression devrait être inférieur d’au moins 15 °C à la température ambiante. • Teneur en huile – Quantité d’huile ≤ 1 mg/m 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Seite 96
Bosch Rexroth AG Postfach 30 02 07 70442 Stuttgart Germany Fax +49 711 811–7777 info@boschrexroth.de www.boschrexroth.com Sous réserve de modifi cations techniques 3 842 358 722/2015-05...
Seite 99
Montaggio dell’unità di posizionamento PE 2 7.5.2 Collegamento pneumatico del prodotto 7.5.3 Montaggio del singolarizzatore VE 2/… Messa in funzione Prima messa in funzione Rischi residui Rimessa in funzione dopo un fermo 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Seite 100
Parti di ricambio Messa fuori servizio Smontaggio e sostituzione 12.1 Preparazione del prodotto per lo stoccaggio/il riutilizzo Smaltimento Ampliamento e trasformazione Ricerca e risoluzione errori Dati tecnici 16.1 Condizioni ambientali 16.2 Pneumatica Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Per poter lavorare in modo rapido e sicuro con il prodotto servendosi della presente documentazione, vengono utilizzate indicazioni di sicurezza, simboli, concetti e abbreviazioni standardizzati. Per facilitarne la comprensione essi sono spiegati nei seguenti paragrafi . 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Se questa informazione non viene rispettata, il prodotto non può essere impiegato né funzionare in modo ottimale. Fase operativa unica, indipendente Istruzione numerata: Le cifre indicano che i passi operativi sono in sequenza. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Qualunque uso diverso da quanto descritto nel paragrafo sull’uso conforme è non conforme e dunque non consentito. La Bosch Rexroth AG non si assume responsabilità alcuna per danni in caso di uso non conforme. In caso di uso non conforme, i rischi sono a carico del solo utente.
• in particolare, comprendere per intero le correlazioni in merito ai dispositivi di sicurezza e • avere conoscenze sul funzionamento e la struttura di componenti pneumatici. Bosch Rexroth offre misure di sostegno alla formazione in campi speciali. All’indirizzo Internet http://www.boschrexroth.de/didactic è disponibile una panoramica dei contenuti dei corsi di formazione.
• Un impianto fermo non è un impianto posto in sicurezza poiché l’energia accumulata può essere rilasciata accidentalmente o a causa di interventi di manutenzione effettuati in maniera non corretta. 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• Prima della prima messa in funzione o della rimessa in funzione, e poi a intervalli di tempo regolari, eseguire una formazione del personale di servizio in materia di sicurezza. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
• Non utilizzare solventi o detergenti aggressivi. Pulire il prodotto esclusivamente con un panno leggermente inumidito di un tessuto che non lascia peli. Utilizzare solo acqua aggiungendo, all’occorrenza, un detergente delicato. • Non utilizzare idropulitrici ad alta pressione per la pulizia. 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• Montaggio nel tratto a nastro BS 2… • Sollevamento del mezzo di trasporto e posizionamento dei pallet WT 2 in una stazione di lavorazione manuale/automatica che richiede un’alta precisione di posizionamento (±0,1 mm). Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
5.2 Descrizione del prodotto Piastra di sollevamento Mandrini di centraggio Scatola di protezione Compensazione dell’altezza Indicazione della direzione di montaggio di PE 2 358 722-01 Fig. 2: Unità di posizionamento PE 2 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• Appoggiare il prodotto solo su una superfi cie piana. • Proteggere il prodotto da infl uenze meccaniche. • Proteggere il prodotto dalle infl uenze ambientali, quali sporco e umidità. • Osservare le condizioni ambientali, vedere pagina 30. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
2 = posizione di serraggio della vite con testa a martello nella scanalatura. Coppia massima: 25 Nm. 7.3 Utensili necessari • Chiave per dadi a testa esagonale (chiave a bocca) SW13. 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Denominazione dei componenti nei grafi ci. Le lettere contrassegnano i componenti citati nel testo di accompagnamento. Vista dettagliata da un’altra visuale, ad esempio sul retro o sul lato inferiore del prodotto. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
fi nché tutte le viti sono serrate. Montare la PE 2. SW13 = 25 Nm ST 2/B ST 2/B-100 M8x40 M8x25 358 722-03 Fig. 4: Montaggio dell’unità di posizionamento PE 2 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Pressione di esercizio: da 4 a 6 bar. Vedere pagina 31. Collegare la PE 2 all’alimentazione G 1/8" dell’aria compressa. G 1/8" 358 722-05 Fig. 5: Schema pneumatico ) Non compreso nella fornitura Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
VE 2/… nella scanalatura del tratto contro la superfi cie laterale di riferimento del pallet. Serrare a fondo le viti del singolarizzatore. 358 722-04 Fig. 6: Montaggio del singolarizzatore VE 2/… 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• Mettere in funzione il prodotto esclusivamente quando tutti dispositivi di sicurezza dell’impianto sono installati e pronti al funzionamento. • Mettere in funzione un prodotto solo se completamente installato. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Mezzo di trasporto: fra Intrappolamento di parti Schiacciamento. mezzo di trasporto e del corpo in fase di pallet. abbassamento. 358 722-11 358 722-12 358 722-13 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• Non scegliere una velocità del tratto di trasporto superiore a quella necessaria per le diverse funzioni. • Particolarmente importante: evitare lo sporco prodotto da agenti abrasivi oppure ridurlo con una pulizia regolare. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
In questi casi è necessaria una particolare attenzione nella fase di progettazione dell’impianto e gli intervalli di manutenzione devono essere ridotti di conseguenza. 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• Manovre di prova con i carter aperti sono consentite solo se effettuate da un esperto che utilizza dip switch e non è possibile che altri organi di movimento possano intervenire. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
• Chiave per dadi a testa esagonale (chiave a bocca) SW10 (2x) SW13, SW19. • Chiave per viti brugola SW3, SW4, SW5. • Cacciavite a stella PZ2 • Calibro, 500 mm • Martello • Punzone 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Sostituzione dell’unità di sollevamento Smontare la piastra di sollevamento. Smontare l’unità di = 8 Nm sollevamento. Sostituire le parti usurate dell’unità di sollevamento. 358 722-22 Fig. 7: Sostituzione dell’unità di sollevamento (1/2) Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Smontare la piastra di sollevamento. Smontare i perni di centraggio (estrarre a pressione) Montare i nuovi perni di centraggio (inserire a pressione). 358 722-21 Fig. 8: Sostituzione dell’unità di sollevamento (2/2) 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Prima di sollevare il prodotto controllare che le cinghie siano fi ssate correttamente! Durante il sollevamento, bloccare il prodotto in modo da impedirne il ribaltamento! Durante il sollevamento e l’abbassamento accertarsi che nessuno oltre all’operatore si trovi nell’area di pericolo! Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
14 Ampliamento e trasformazione • Non trasformare il prodotto. • La garanzia di Bosch Rexroth copre solo la confi gurazione fornita e gli ampliamenti compatibili con la confi gurazione. La garanzia decade dal momento in cui si applica una trasformazione o un ampliamento che vanno al di là delle operazioni contemplate dalle presenti istruzioni.
≤ +3 °C ) Il punto di rugiada in pressione dovrebbe essere di almeno 15 °C inferiore rispetto alla temperatura ambiente. • Contenuto di olio – Quantità di olio ≤ 1 mg/m 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Seite 128
Bosch Rexroth AG Postfach 30 02 07 70442 Stuttgart Germany Fax +49 711 811–7777 info@boschrexroth.de www.boschrexroth.com Soggetto a modifi che tecniche 3 842 358 722/2015-05...
Seite 131
Montaje de la unidad de posicionamiento PE 2 7.5.2 Conexión neumática del producto 7.5.3 Montaje del separador VE 2/… Puesta en marcha Primera puesta en marcha Riesgos residuales Nueva puesta en marcha después de una parada 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Seite 132
Puesta fuera de servicio Desmontaje y sustitución 12.1 Preparación del producto para el almacenamiento/reutilización Eliminación Ampliación y transformación Búsqueda de fallos y su solución Datos técnicos 16.1 Condiciones ambientales 16.2 Neumática Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Para que pueda trabajar rápidamente y de forma segura con el producto usando esta documentación se utilizan siempre las mismas indicaciones de seguridad, símbolos, términos y abreviaturas. Para facilitar la comprensión, estos vienen explicados en los apartados siguientes. 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Si no se tiene en cuenta esta información, no se podrá utilizar el producto de forma óptima. Instrucción única, independiente Serie de acciones numeradas: Las cifras indican que se debe ir ejecutando un paso tras otro. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Cualquier otro uso que difi era del especifi cado en la utilización correcta se considera incorrecto y, por lo tanto, no está autorizado. Bosch Rexroth AG no asume responsabilidad alguna por aquellos daños que se deban a una utilización no correcta. Los riesgos que se deriven de una utilización no correcta son responsabilidad exclusiva del usuario.
• Disponer de conocimientos sobre el funcionamiento y la estructura de los componentes neumáticos. Bosch Rexroth le ofrece medidas de apoyo a la formación en determinadas áreas. Encontrará un resumen de los contenidos en la página de Internet: http://www.boschrexroth.de/didactic.
– los accesos a los mandos de parada de emergencia estén libres de obstáculos. – todos los puntos de transferencia, puestos de trabajo y pasos estén libres. • No utilice los mandos de parada de emergencia para detener la instalación en condiciones normales. 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• Realice una instrucción de seguridad del personal de trabajo antes de la primera puesta en funcionamiento o antes de volver a poner en funcionamiento el producto y, luego, en intervalos regulares. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
fi bras ligeramente humedecido. Para ello utilice solo agua y un poco de un producto de limpieza suave si es necesario. • Para la limpieza no utilice ningún limpiador de alta presión. 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• Montaje en tramo de cinta BS 2... • Elevación de medio de transporte y posicionamiento de portapiezas WT 2 en una estación de mecanizado manual/automática con requisitos estrictos en cuanto a exactitud de posicionamiento (±0,1 mm) Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Placa de elevación Perno de centrado Caja de protección Compensador de altura Indicación del sentido de montaje de la PE 2 358 722-01 Fig. 2: Unidad de posicionamiento PE 2 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• Proteja el producto frente a efectos mecánicos. • Proteja el producto de los efectos medioambientales, como la suciedad y la humedad. • Tenga en cuenta las condiciones ambientales; véase la página 30. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
2 = posición de apriete del tornillo de cabeza de martillo en la ranura Par de apriete máximo: 25 Nm 7.3 Herramientas necesarias • Llave de boca hexagonal de ancho 13 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Las letras identifi can a los componentes indicados en el texto que los acompañan. Vista en detalle desde otro punto de vista, por ejemplo vistas sobre la parte posterior o inferior del producto. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Monte la PE 2. SW13 = 25 Nm ST 2/B ST 2/B-100 M8x40 M8x25 358 722-03 Fig. 4: Montaje de la unidad de posicionamiento PE 2 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Véase la página 31. Conecte la PE 2 a la alimentación de aire G 1/8" comprimido. G 1/8" 358 722-05 Fig. 5: Esquema neumático ) No incluido en el volumen de suministro Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
VE 2/… premontado en la ranura del tramo contra el canto de tope del portapiezas. Apriete bien los tornillos del separador. 358 722-04 Fig. 6: Montaje del separador VE 2/… 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• Ponga el producto en marcha solo si todos los dispositivos de seguridad están instalados y operativos. • Ponga en marcha sólo un producto completamente instalado. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
fi jo Medio de transporte: Aprisionamiento de Aplastamiento entre el medio de partes del cuerpo al transporte y el descender portapiezas 358 722-11 358 722-12 358 722-13 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• No seleccione una velocidad para el tramo de transporte que exceda la velocidad que requiere la función. • Especialmente importante: evite la suciedad con medios abrasivos o redúzcala con una limpieza regular. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Estos casos requieren especial cuidado al planifi car la instalación y un ajuste de los intervalos de mantenimiento. 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• Solo se pueden realizar marchas de prueba con los revestimientos abiertos si se encarga de ello una persona cualifi cada utilizando interruptores de paso a paso y no existe posibilidad de que actúen otros mecanismos de conmutación. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
10 (2 uds.), 13 y 19 • Llaves Allen de anchos 3, 4 y 5 • Destornillador de estrella PZ2 • Calibre de 500 mm • Martillo • Mandril 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Desmonte la unidad de = 8 Nm elevación. Sustituya las piezas de la unidad de elevación que estén desgastadas. 358 722-22 Fig. 7: Cambio de la unidad de elevación (1/2) Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Desmonte la placa de elevación. Desmonte las clavijas de centrado (extraer a presión). Monte las clavijas de centrado nuevas (introducir a presión). 358 722-21 Fig. 8: Cambio de la unidad de elevación (2/2) 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Asegure el producto al levantarlo para evitar que vuelque. Durante las tareas de elevación y bajada, asegúrese de que, a excepción del operario, no se encuentre nadie más en la zona de peligro. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
14 Ampliación y transformación • No está permitido transformar el producto. • La garantía de Bosch Rexroth cubre solamente la confi guración entregada y las ampliaciones que se han tenido en cuenta durante la confi guración. Tras una transformación o una ampliación que va más allá de las descritas aquí, la garantía se extingue.
Rexroth. • Debe evitarse el contacto prolongado con sustancias de alta reacción básica o alcalina. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
) El punto de condensación de presión debe situarse por lo menos 15 °C por debajo de la temperatura ambiente. • Contenido de aceite – Volumen de aceite ≤ 1 mg/m 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Seite 160
Bosch Rexroth AG Postfach 30 02 07 70442 Stuttgart Germany Fax +49 711 811–7777 info@boschrexroth.de www.boschrexroth.com Reservado el derecho a realizar modifi caciones. 3 842 358 722/2015-05...
Seite 161
PE 2 Unidade de posicionamento É válido para os seguintes tipos: 3 842 504 706 3 842 504 711 3 842 504 716 3 842 504 707 3 842 504 712 3 842 504 717 3 842 504 708 3 842 504 713 3 842 504 718 3 842 504 709 3 842 504 714...
Seite 162
ZH 中文 media PE 2 定位单元 3 842 358 722 print MTCS 358 722 media PE 2 Polohovací jednotka CS Česky MTPL 358 722 media PE 2 Układ pozycjonujący PL Polski Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Seite 163
Montar a unidade de posicionamento PE 2 7.5.2 Fazer a conexão pneumática do produto 7.5.3 Montar o separador VE 2/… Colocação em funcionamento Primeira colocação em funcionamento Riscos residuais Nova colocação em funcionamento após paralisação 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Seite 164
Retirar de funcionamento Desmontagem e substituição 12.1 Preparar o produto para o armazenamento/reutilização Eliminação Ampliação e alteração da montagem Busca e solução de falhas Dados técnicos 16.1 Condições ambientais 16.2 Pneumática Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Para poder trabalhar com rapidez e segurança com o seu produto, usando este documento, são usadas instruções de segurança, símbolos, termos e abreviaturas uniformizados. Para melhor compreensão, estes são explicados nos trechos seguintes. 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Se esta informação não for observada, o uso ou operação do produto não serão os melhores possíveis. Procedimento individual e independente Instrução de procedimento numerada: Os números indicam a ordem sequencial dos passos do procedimento. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Qualquer outro uso que não o descrito no uso correto, é considerado incorreto e, por isso, não permitido. A Bosch Rexroth AG não se responsabiliza por danos causados pelo uso incorreto. Nesse caso, o risco será apenas do usuário. Igualmente incorretas são as seguintes aplicações indevidas previsíveis: •...
• especialmente, compreender na íntegra as relações que dizem respeito aos dispositivos de segurança e • ter conhecimentos sobre o funcionamento e construção de peças pneumáticas. A Bosch Rexroth oferece ações de treinamento em áreas especiais. Você poderá encontrar uma visão geral dos conteúdos dos treinamentos na Internet em: http://www.boschrexroth.de/didactic 2.5 Instruções gerais de segurança...
• Após uma PARADA DE EMERGÊNCIA, em caso de erro ou outras irregularidades, desligue o produto e proteja-o para que não seja religado inadvertidamente. • Nunca toque em peças em movimento. 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
área de trabalho ou de tráfego. • Execute, antes do primeiro ou do novo comissionamento, e depois regularmente, instruções de segurança do pessoal operacional. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
fi apos. Use apenas água e, se necessário, um produto de limpeza suave. • Para a limpeza não use máquinas de alta pressão. 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• Montagem na via de esteira BS 2… • Elevação do meio de transporte e posicionamento de paletes porta-peças WT 2 em uma estação de processamento manual/automática com exigências de alta precisão do posicionamento (±0,1 mm). Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
5.2 Descrição do produto Placa de elevação Pinos de centralização Caixa protetora Compensação da altura Indicação da direção de montagem da PE 2 358 722-01 Fig. 2: Unidade de posicionamento PE 2 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• Proteja o produto contra infl uências mecânicas. • Proteja o produto contra as infl uências ambientais, como a sujeira e umidade. • Observe as condições ambientais, ver página 30. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Designação dos componentes em gráfi cos. As letras indicam os componentes mencionados no texto em anexo. Vista detalhada a partir de outra direção de visualização, por exemplo, da parte traseira ou parte inferior do produto. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Monte a PE 2. SW13 = 25 Nm ST 2/B ST 2/B-100 M8x40 M8x25 358 722-03 Fig. 4: Montar a unidade de posicionamento PE 2 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Pressão de serviço: 4 a 6 bar. Ver página 31. Ligue a PE 2 à alimentação de ar G 1/8" comprimido. G 1/8" 358 722-05 Fig. 5: Esquema pneumático ) não incluído no lote de fornecimento Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
VE 2/… pré-montado na ranhura da via contra a aresta de encosto da palete porta-peças. Aperte bem os parafusos do separador. 358 722-04 Fig. 6: Montar o separador VE 2/… 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• Coloque o produto em funcionamento apenas se todos os dispositivos de segurança da instalação estiverem montados e prontos para funcionar. • Coloque o produto em funcionamento somente se estiver completamente instalado. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Meio de transporte: Entalar partes do corpo Esmagamento. entre o meio de durante o abaixamento. transporte e palete porta-peças. 358 722-11 358 722-12 358 722-13 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• A velocidade da via de transporte não deve ser ajustada mais alta do que o necessário para a respectiva função. • Especialmente importante: evite sujeira através de agentes abrasivos, reduza a sujeira através de limpeza regular. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Em tais casos, é necessário dar uma atenção especial ao planejamento da instalação e os intervalos de manutenção devem ser correspondentemente encurtados. 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
• As ativações para fi ns de teste com as coberturas abertas somente são permitidas se forem executadas por uma pessoa capacitada, usando ligações por períodos extremamente curtos e sem que possa haver a infl uência de outro dispositivo de ativação. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Desmonte a placa de elevação. Desmonte a unidade de = 8 Nm elevação. Substitua as peças desgastadas da unidade de elevação. 358 722-22 Fig. 7: Substituir a unidade de elevação (1/2) Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Desmonte a placa de elevação. Desmonte a cavilha central (pressionar para fora). Monte a cavilha central nova (pressionar para dentro). 358 722-21 Fig. 8: Substituir a unidade de elevação (2/2) 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
fi xadas corretamente! Durante o levantamento, proteja o produto para evitar que tombe! Enquanto estiver levantando e abaixando, certifi que-se de que não há ninguém na área de perigo além do operador! Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
14 Ampliação e alteração da montagem • Você não pode alterar o produto. • A garantia da Bosch Rexroth é válida apenas para a confi guração fornecida e as ampliações consideradas na confi guração. Após uma alteração ou ampliação não previstas e descritas neste documento, a garantia perderá...
óleo de controle, óleos ligados, substâncias detergentes agressivas, solventes ou fl uido para freios, recomendamos uma consulta ao seu representante especializado Rexroth. • O contato prolongado com substâncias de forte reação ácida ou básica deve ser evitado. Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
) ≤ +3 °C ) O ponto de condensação de pressão deveria se situar, no mínimo 15 °C abaixo da temperatura ambiente. • Teor de óleo – Quantidade de óleo ≤ 1 mg/m 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...
Seite 192
Bosch Rexroth AG Postfach 30 02 07 70442 Stuttgart Germany Fax +49 711 811–7777 info@boschrexroth.de www.boschrexroth.com Direitos de modifi cações reservados 3 842 358 722/2015-05...
Seite 194
ZH 中文 media PE 2 定位单元 3 842 358 722 print MTCS 358 722 media PE 2 Polohovací jednotka CS Česky MTPL 358 722 media PE 2 Układ pozycjonujący PL Polski Bosch Rexroth AG, MIT: PE 2, 3 842 358 722/2015-05...
Seite 195
产品铭牌 运输和储存 产品的运输 产品的储存 安装 拆包装 安装条件 安装位置 7.2.1 使用 T 型螺栓固定 7.2.2 必要的工具 使用的符号 产品安装 安装定位单元 PE 2 7.5.1 产品气动连接 7.5.2 安装挡停器 VE 2/… 7.5.3 初次运行 首次初次运行 伤害风险 停用后重新投入使用的初次运行 3 842 358 722/2015-05, MIT: PE 2, Bosch Rexroth AG...