Technical Data; Before Starting The Machine; Setting The Cutting Height - EINHELL BG-BC 25/1 Bedienungsanleitung

Anleitung BG_BC_25_1_SPK1:_

4. Technical data

Engine type
2-stroke engine, air-cooled, chrome cylinder
Engine power (max.)
Displacement
Idle speed of engine
Max. engine speed
Max. twin line speed
Ignition
Drive
Weight (with empty tank)
Long handle length
Cutting circle diameter of line
Cutting circle diameter of blade
Cutting line length
Cutting line diameter:
Tank capacity
Spark plug
Vibration a
hv
Idling speed (max.)
Idling speed (max.)
L sound pressure level
pA
L sound power level
WA
5. Installation
5.1 Installing the long handle
Install the long handle as shown in Figures D1 – D3.
Do not tighten the screws until you have set the
perfect working position with the carrying strap. The
long handle should be aligned as shown in Figure A.
5.2 Fitting / Replacing the blade (Fig. E1 – E7)
The fitting of the cutting blade is shown in Figures
E1 - E7.
Push the lower carrier plate (Fig. E2/Item A) over
the spline shaft.
Securely fit the cutting blade (Fig. E3/Item 4) onto
the lower carrier plate.
Slide the upper carrier plate (Fig. E4/Item B) over
the thread.
Push the cover plate (Fig. E5/Item C) over the
thread.
12.01.2009 8:11 Uhr Seite 19
Look for the hole in the lower carrier plate and line
up with the notch beneath it, then securely fasten
the carrier plate using the Allen key (size 5).
Securely tighten the locknut (Fig. E6/Item D).
5.3 Fitting / Replacing the line spool
0.75 kW/1 hp
Line up the hole in the carrier plate with the notch
25.7 cc
beneath it and securely fasten the carrier plate using
the Allen key (size 5). Secure the line spool on to the
3000 rpm
locating pin (Fig. F8).
8000 rpm
Important: Left-hand thread!
6,200 rpm To dismantle, proceed in reverse order.
Electronic
5.4 Mounting the blade guard hood
Centrifugal clutch
Important: The cutting blade guard hood must be
fitted if you wish to work with the cutting blade. The
6.3 kg
guard hood for the cutting blade must be installed as
142 cm
shown in Figures F1 – F3. Slide the blade guard hood
Ø 42 cm
between the fastening plate and the plastic mount
(Fig. F1/Item 2). Insert the fastening screws through
Ø 25,5 cm
the holes from the bottom (Fig. F2/Item 26).
3.0 m
Now securely tighten the fastening nuts (Fig. F3/Item
2.4 mm
27). To do so, hold the fastening screws (26) steady
with the Allen key (size 4).
0.45 l
L8RTC
5.5 Fitting the cutting line guard hood
Important: The cutting line guard hood must be fitted
if you wish to work with the line spool.
3.62 m/s 2
4.99 m/s 2
Fitting:
101 dB (A)
Slide the detents of the cutting line guard hood (3)
into the openings of the blade guard hood (2) and
110 dB (A)
ensure that the cutting line guard hood is properly and
securely fitted (Fig. F4).
Removing:
Press the detents of the cutting line guard hood and
remove the hood by pulling it out.

6. Before starting the machine

Check that all moving parts move smoothly before
you start using the machine. Check that all screw
connections are securely fastened and also check all
the safety devices.

6.1 Setting the cutting height

Fit the carrying strap as shown in Figures G1 –
G3.
Hook the machine to the carrying belt (Fig. G4).
Adjust the perfect working and cutting position
using the various strap adjusters on the carrying
strap (Fig. G5).
In order to establish the optimum length of the
GB
19