Initial Startup; Operation - Kärcher LM 530/36 Bp Originalbetriebsanleitung

Battery pack release
1
Charge indicator
2
Type plate
3
Push Assist lever
4
ON/OFF lever
5
Slider speed control
6
Starter button
7
Motor control cable
8
Telescopic handle
9
Handle lock
10
Grass bag
11
Quick-release catch
12
Cutting height adjustment lever
13
Cutting height display
14
Fall protection
15
Mulch plug
16
*Side ejector
17
Safety key
18
*Battery Pack Battery Power+ 36V (2x)
19
*Quick Charger Battery Power+ 36V
20
* optional
Rechargeable battery pack
The device can be operated with two 36 V Kärcher Bat-
tery Power+ battery packs.

Initial startup

Adjusting the handle
1. Fold over the telescopic handle.
a Pull out both quick-release catches.
Illustration B
b Turn the quick-release catches.
The quick-release catches are unlocked.
c Fold over the telescopic handle.
d Lock the quick-release catches.
2. Extend the telescopic handle.
a Unlock the handle locks.
Illustration C
b Pull the telescopic handle out completely.
c Lock the handle locks.
Note
The device only functions when the telescopic handle
has been completely pulled out and the handle locks are
locked.
3. Adjust the inclination angle of the handle if neces-
sary.
a Pull out both quick-release catches.
Illustration B
b Turn the quick-release catches.
The quick-release catches are unlocked.
c Choose the inclination angle.
d Lock the quick-release catches.
Attaching the mulch plug
The mulch plug is used when the mown grass is to re-
main on the lawn.
1. Pull up the handle of the mulch plug.
Illustration E
2. Install the mulch plug in the ejection chute.
Illustration F
3. Pull down the handle of the mulch plug.
The mulch plug is locked in the device.
Mount the grass bag
The grass bag is used when the mown grass is to be
collected for disposal.
1. Remove the mulch plug if necessary.
a Pull up the handle of the mulch plug.
Illustration G
The mulch plug is unlocked.
b Remove the mulch plug from the ejection chute
2. Hook the grass bag to the ejection chute.
Illustration H
Mounting the side ejector
The side ejector is used when the grass clippings are to
be ejected sideways.
1. Remove the mulch plug if necessary.
a Pull up the handle of the mulch plug.
Illustration G
The mulch plug is unlocked.
b Remove the mulch plug from the ejection chute
2. Hook in the side ejector on the ejection chute.
Illustration I
Mount the battery pack
1. Push the battery pack into the mounting in the de-
vice until it audibly latches into place.
Illustration J
Insert the security key
1. Use the security key.
Illustration K
The mark on the security key indicates which battery
pack is used during operation.
General information on handling the
The run time of the battery depends on several factors:
 The condition, length and density of the grass
 The cutting height setting
Maximum surface performance depending on the state
of the grass: approx. 2500 m
The results of the mowing process can be optimised as
follows:
 Cut at a maximum of one third of the grass height.
 When mowing tall grass, reduce the speed at which
the device is pushed or moves forward when the
push-assist function is activated.
Note
Do not mow wet grass. Wet grass sticks to the under-
side of the lawnmower and prevents correct collection of
the grass in the grass bag or ejection of the grass.
WARNING
Lifting or tipping the lawnmower during operation
Incision injuries
The blade of the lawnmower rotates approximately par-
allel to the ground over which it moves. Take care to en-
sure that all four wheels touch the ground when
mowing.
English

Operation

lawnmower
2
.
Mowing lawns
21