Conrad 61 07 09 Bedienungsanleitung Seite 4

Attaching the mounting plate
Please refer to the section "Safety Information"!
• First, remove the mounting plate by rotating it slightly
counter-clockwise.
• Fasten the mounting plate with two screws and plugs to
the ceiling.
Use screws and plugs that are suitable for the surface.
Pay attention when drilling/tightening the
screws that no power, gas or water pipes are
damaged!
• After connecting the cables (see next chapter), the mo-
tion switch needs to be attached to the mounting plate
and locked by rotating it clockwise.
Make sure that the cables are not pinched or damaged!
Connection
Connect the connection cables to the corresponding
screw terminals (observe labels):
L = Phase (brown cable)
N = Neutral wire (bleu cable)
A = Switch output (red cable)
Please pay attention to the example circuit in the
picture on the right, or the imprint in the housing next
to the screw terminals.
Controls on the motion switch
• Setting the on-time (control knob "TIME")
Using this control, you can set the duration time for the connection L'. Turning the control
knob counter clockwise, to the left, shortens the on-time, turning it to the right lengthens it.
If a further motion is detected during the on-time, the time for the on-time starts again.
• Setting the brightness (control knob "LUX")
This knob allows the switching threshold to be set, i.e. the ambient brightness at which the
motion switch is activated.
Turning the knob towards the moon symbol, means the motion detector activates when it is
darker, turning it to the left, towards the sun symbol, activates the motion detector in brighter
conditions.
If you want to carry out a function test by daylight, turn the control knob fully to the left.
Opeleveln
As already explained in the chapter "Function of the motion switch", the PIR movement sensor
in the motion switch responds to temperature changes in the detection area.
When a temperature changes is detected, the relay is activated and switches on the connected
power consumer for the set time. The LED on the movement switch is also activated. If new
motion is detected during the on-time, the on-time duration starts once again, the consumer
stays switched on.
When a temperature change is no longer detected, the connected consumer is switched off.
Maintenance and Care
The motion switch is maintenance free. For this reason, you should never open it or take it
apart (except for the installation described in this manual). Maintenance or repairs may only be
performed by qualifi ed personnel.
Occaisonally clean the hemispherical diffusion panel on the motion switch from dust or sedi-
ments; only use a dry, clean and soft cloth.
Motion switch
220-240 V/AC
50 Hz
Disposal
Dispose of an unserviceable product in accordance with the relevant statutory regu-
lations.
Technical Data
Operating voltage .........................220 - 240 V/AC, 50 Hz
Power consumption ......................approx. 0.45 W
Switching power (connection A) ...1200 W (resistive load)
300 W (inductive load)
☞
Devices with mainly resistive load are, e.g., light bulbs, heaters, etc.
Devices with inductive load are, e.g., engines, control gears, conventional trans-
formers, energy saving bulbs, etc.
Mounting location ......................... Wall or ceiling installation, only in dry, enclosed interiors.
On-time time ................................adjustable, 10 seconds (±3 seconds)
up to 7 minutes (±2 minutes)
Ambient brightness .......................adjustable, 3 - 2000 lux
Viewing angle ...............................360°
PIR range .....................................approx. max. 6 m (at +24 °C)
Installation height: .........................2.4 to 4 m (recommended max. 3 m)
Ambient temperature .................... 0 °C to +40 °C (decreased range at temperatures higher
than +24°C)
Ambient air humidity .....................0% to max. 93 % relative air humidity, not condensing
Dimensions (Ø x h): ......................115 x 57 mm
Weight ..........................................approx. 167 g
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfi lming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2012 by Conrad Electronic SE.