Inhaltsverzeichnis
Werbung
{
Possible settings
...
Security LED (on/off)
BLK ON
"
" The Security LED flashes if the
Activating coding (for details, see the
radio is switched off and the
chapter "Coding", page 15).
vehicle's motor is not running.
BLK OFF
CODE
If "
" appears in the display, coding is
"
" The Security LED does not
flash.
not activated.
SAFE
If "
" appears in the display, coding is
Sound signal (on/off)
activated.
BEEP ON
"
" Sound signal as function con-
Display brigthness
firmation.
DISPL 07
BEEP OFF
"
" (00 ... 07). Set according to the
"
" Function confirmation
location of the car radio so that
through brief muting of the
the display can optimally be read
loudspeaker outputs.
off.
Autom. LEARN (radio mode)
If you havec connected the car radio to
If you are in a reception area in which
the illumination contact of the vehicle's
plug connector, the display brightness will
reception of RDS programmes with traffic
change if the headlights of the vehicle are
announcements is poor, you can disable
switched on (night setting) or off (day
the autom. LEARN function in radio mode.
setting). Both settings can separately be
LRN ON
"
": autom. LEARN
selected and stored in memory with
LRN OFF
"
": no autom. LEARN.
switched on or switched off headlights.
If the volume is set below "
LRN ON
"
" setting is supposed.
Coding
Activating the coding
Your personal code number is on the iden-
tity card of your car radio.
1. Select the EXPERT control level and turn
Coding is not activated when the radio lea-
¢ ¢
the left-hand
control knob until "
ves the factory.
appears in the display.
Activate the change mode:
If you have "activated" your car radio's
Briefly press the right-hand
coding: As soon as you disconnect the car
knob. The display indicates " CH - - - - "
radio from the car battery (or permanent
(CH = Change).
plus terminal 30), it is electronically
blocked.
2. Enter the code number (on the Identity
Only you are able to put it back into opera-
Card): Use the right-hand
tion by entering your personal Code Number.
to enter the correct number.
When the right-hand
Is the coding activated?
turned quickly, it will function like a
Activate the EXPERT mode and turn the
flywheel.
¢ ¢
left-hand
control knob until the display indi-
3. Confirm the code number:
SAFE
CODE
cates "
" or "
".
Briefly press the right-hand
SAFE
"
" appears in the display.
Coding is activated!
4. Deactivate the EXPERT control level:
Press the
¡
button or the right-hand
Coding activated.
¢ ¢
control knob until the signal sounds.
Coding not activated.
EXPERT
Autom. change of regional programme
If an RDS programme consists of various
regional programmes, it may occur that
your car radio changes between regional
stations when changing the reception area.
REG ON
"
" autom. change of regional
programme is possible.
REG OFF
"
" no change of regional
programme is possible.
Switching on and off with the
ignition/start switch
IGN ON
"
" It is possible to switch the radio
on and off with the ignition/start
switch of the vehicle.
IGN OFF
"
" Switching on and off is only
¡
possible with the
IO
button.
Muting in telephone mode
PHONE ON
"
" Muting activated.
PHONE OFF
"
" Muting deactivated.
VOL 4
", the
Deactivating coding
before removing the car radio, for example.
CODE
"
1. The EXPERT mode must be switched on
SAFE
and "
" indicated in the display.
Activate the change mode:
¢ ¢
control
¢ ¢
Briefly press the right-hand
control
knob. The display indicates " CH 1 - - - - "
(CH = Change).
2. Enter the code number (on the Identity
¢ ¢
control knob
¢ ¢
Card) by turning the right-hand
control
knob as described under "Activating
¢ ¢
control knob is
Coding"
3. Confirm the code number:
¢ ¢
Press the right-hand
control knob until
CODE
"
" appears briefly in the display.
¢ ¢
The radio will play after approximately
control knob.
3 seconds.
Coding is deactivated!
If you have entered the incorrect code
number:
SAFE
"
" remains in the display and the radio
does not play.
Begin again. Be sure to observe the waiting
periods between attempts (see page 16).
MCD and AUX input sensitivity
CLOCK ON/OFF
CLOCK ON
to adjust the sensitivity to a CD changer.
"
" Time indication on.
MCD LOW
CLOCK OFF
"
" low
"
" Time indication off.
MCD MID
"
" medium
u
Clock synchronization
(eg. MCD 36/MCD 40)
MCD HIGH
sync ON
"
" high
"
"
The built-in clock is
m
synchronized by RDS
Volume limitation when switching on
signals.
ON VOL - -
sync OFF
"
": no limitation
"
" In areas where no RDS
ON VOL 20
"
": max. volume, eg., 20
TIMER signals are received,
(- - ... 46).
the synchronization func-
The volume is limited only if the volume
tion can be deactivated.
when the car radio is switched off is
{
DIGITIME
greater than the set value!
TM 00:00
"
" This function serves for
Minimum volume for traffic
manual time setting. If you
announcements
turn the right-hand control
TA VOL 16
knob quickly, it will act as a
"
" (5 ... 46)
flywheel.
The volume for the traffic announcement
can be heard during setting.
sync ON
If "
" has been selected (see
the manually set time may be corrected
by the currently received RDS station.
If this RDS station should transmit an
undesired time, you must disable this
correction by selecting "
Return to operation
Waiting periods
With coding activated, the car radio is electro-
To prevent deactivation of the coding being
nically disabled after it has been disconnected
possible by trial and error, waiting periods are
from the car battery (or permanent plus, ter-
required between attempts. During these wait-
minal 30), e.g. after the radio has been remo-
ing periods, the car radio can be switched on
ved during servicing.
and off but will not play.
1. Switch on the car radio.
During the waiting period
SAFE
The display indicates "
".
the car radio needs not be switched on, but
After approx. 3 seconds, the display indi-
it must be connected to the permanent +12 V
I - - - -
I
voltage. As long as the display indicates
cates "
". The "
" stands for the
SAFE
number of attempts.
"
", the waiting period has not yet elapsed.
The waiting period is over when the number
2. Enter the code number (on Identity Card),
of the next attempt is visible in the display,
by turning the right-hand
¢ ¢
control knob
2 - - - -
e.g. "
".
as described in the chapter "Activating
The table shows
Attempt
coding".
the waiting
(in display)
3. Confirm the code number:
periods between
¢ ¢
Press the right-hand
control knob until
the individual
SAFE
"
" appears briefly in the display.
attempts.
After approximately 3 seconds the radio
Waiting period
will play.
after the 7th
attempt is always
If you have entered the incorrect code
24hrs!
number:
SAFE
After the 6th
"
" remains in the display and the radio
attempt we
does not play.
recommend having a dealer complete the
Begin again. Be sure to observe the waiting
"Return to operation" or "Deactivate coding"
periods between attempts.
process.
EXPERT
u
),
sync OFF
".
Installation and removal
Coding
Installation materials and accessories
Your dealer can advise you as to what installa-
tion materials you will need and what acces-
sories are available. The Figures are to be
found at the end of this booklet.
Installing the mounting frame
Figure
– Insert mounting frame b into cutout a of the
vehicle.
– Bend the tabs c behind cutout a as required
(depending on type of vehicle).
Inserting the car radio
Wait.per.
(approx.)
Figure
1
21 sec.
– Insert the car radio all the way into the
2
1.5 min.
installed mounting frame b.
3
5.5 min.
The car radio should snap into place.
4
22 min.
5
Removing the car radio
1.5 hrs.
6
6.0 hrs.
7
Figure
24 hrs.
8
Insert the two removal handles d as far as
24 hrs.
possible into the openings in the trim.
Press both removal handles outwards and
slowly pull the radio out.
Werbung
Inhaltsverzeichnis
