General Power Tool Safety Warnings; Specific Safety Rules - Makita 4351T Bedienungsanleitung

Uncertainty (K) : 3 dB(A)
Wear ear protection
Vibration
The vibration total
determined according to EN60745-2-11:
Work mode : wood cutting
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : metal cutting
Vibration emission (a
Uncertainty (K) : 1.5 m/s
The declared vibration emission value has been
•
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
The declared vibration emission value may also be
•
used in a preliminary assessment of exposure.
WARNING:
The vibration emission during actual use of the
•
power tool can differ from the declared emission
value depending on the ways in which the tool is
used.
Be sure to identify safety measures to protect the
•
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
EC Declaration of Conformity
We Makita Corporation
manufacturer declare that the following Makita
machine(s):
Designation of Machine:
Jig saw
Model No./ Type: 4351T, 4351CT, 4351FCT
are of series production and
Conforms to the following European Directives:
98/37/EC until 28th December 2009 and then with
2006/42/EC from 29th December 2009
And are manufactured in accordance with the following
standards or standardised documents:
EN60745
The technical documentation is kept by our authorised
representative in Europe who is:
Makita International Europe Ltd,
Michigan, Drive, Tongwell,
Milton Keynes, MK15 8JD, England
30th January 2009
000230
Tomoyasu Kato
value (tri-axial vector
2
) : 6.5 m/s
h,CW
2
2
) : 4.5 m/s
h,CM
2
as the responsible
ENG220-1
sum)
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
ENG304-1
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
ENG901-1
Save all warnings and instructions for
future reference.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to jig saw safety rules. If you use this tool unsafely
or incorrectly, you can suffer serious personal
injury.
1. Hold
surfaces, when performing an operation
where the cutting accessory may contact
hidden wiring or its own cord. Cutting
accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
2. Use clamps or another practical way to secure
and support the workpiece to a stable platform.
ENH101-12
Holding the work by hand or against your body
leaves it unstable and may lead to loss of control.
3. Always
Ordinary eye or sun glasses are NOT safety
glasses.
4. Avoid cutting nails. Inspect workpiece for any
nails and remove them before operation.
5. Do not cut oversize workpiece.
6. Check for the proper clearance beyond the
workpiece before cutting so that the blade will
not strike the floor, workbench, etc.
7. Hold the tool firmly.
8. Make sure the blade is not contacting the
workpiece before the switch is turned on.
9. Keep hands away from moving parts.
10. Do not leave the tool running. Operate the tool
only when hand-held.
11. Always switch off and wait for the blade to
come to a complete stop before removing the
blade from the workpiece.
12. Do not touch the blade or the workpiece
immediately after operation; they may be
extremely hot and could burn your skin.
13. Do
unnecessarily.
5
Director
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, JAPAN
power tool by insulated
use safety glasses or goggles.
not operate the
GEA010-1
GEB016-2
gripping
tool at no-load