Bosch GSH 11 E Professional Originalbetriebsanleitung Seite 12

OBJ_BUCH-66-006.book Page 12 Wednesday, April 20, 2011 2:59 PM
12 | English
1 Dust protection cap
2 Locking sleeve
3 Chisel adjustment ring (Vario-Lock)
4 On/Off switch
5 Thumbwheel for preselection of impact rate
6 Service indicator
7 Auxiliary handle (insulated gripping surface)
8 Knurled nut for auxiliary handle
9 Handle (insulated gripping surface)
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.
Technical Data
Demolition Hammer
Article number
Rated power input
Impact rate
Impact energy per stroke accord-
ing to EPTA-Procedure 05/2009
Chisel positions
Chiselling capacity in concrete of
medium hardness
Tool holder
Lubrication
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your machine.
The trade names of the individual machines may vary.
Noise/Vibration Information
Measured sound values determined according to
2000/14/EC.
Typically the A-weighted noise levels of the product are:
Sound pressure level 89 dB(A); sound power level
100 dB(A). Uncertainty K=3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2
Chiselling: a = 16 m/s , K= 1.5 m/s
h
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
1 609 929 X25 | (20.4.11)
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2004/108/EC,
GSH 11 E
2006/42/EC, 2000/14/EC.
Professional
2000/14/EC: Guaranteed sound power level 105 dB(A).
0 611 316 7..
Conformity assessment procedure according to Annex VI.
W 1500
Equipment category: 10
-1
min 900 – 1890
Notified body:
TÜV NORD CERT GmbH & Co. KG,
Am TÜV 1, 30519 Hannover
J 16.8
Technical file at:
12
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
kg/h 490
Dr. Egbert Schneider
SDS-max
Senior Vice President
Central
Engineering
permanent lubri-
cation
kg 10.1
Robert Bosch GmbH, Power Tools Division
/II
D-70745 Leinfelden-Echterdingen
30.07.2010
Assembly
Auxiliary Handle
Operate your machine only with the auxiliary handle 7.
The auxiliary handle 7 can be set to any position for a secure
and low-fatigue working posture.
Loosen the knurled nut 8, rotate the auxiliary handle 7 around
the axis of the machine to the required position and tighten
the knurled nut 8 again.
The auxiliary handle 7 can be mounted to a different position.
For this, completely unscrew the knurled nut 8 and then pull
2
.
out the hexagon bolt upward. Pull off the auxiliary handle 7 to
the side and turn around the remaining clamping element by
180°. Mount the auxiliary handle 7 in reverse order.
Changing the Tool
Before any work on the machine itself, pull the mains
plug.
With the SDS-max tool holder, simpler and easier tool chang-
ing is possible without additional aids.
Dr. Eckerhard Strötgen
Head of Product
Certification
Bosch Power Tools