WOODLAND SCENICS DPM LANDMARK STRUCTURES N BUILDING KIT Bauanleitung

DPM
INSTRUCTIONS
Read through instructions before beginning.
Use plastic cement to glue parts. Plastic cement works by dissolving the surface of plastic and
welding parts together. Be careful to avoid contact with detail on parts and visible areas on Clear
Window Material. Always allow glue to set before moving to next construction step.
Prepare Building Parts
Wash Walls, Door and Chimney Backs in warm, soapy water, rinse and let dry. Use a hobby knife
and sandpaper to remove excess plastic (tabs and flash) that occurred during the molding process.
Tabs: Score flush with part, snap off and sand smooth. Flash: Lightly scrape along edges to remove
debris and sand smooth. Face cutting edge of blade opposite the scraping direction to avoid cutting
into detail on Walls. NOTE: Some Walls have alignment pins molded onto the backside to assist in
proper alignment. Do not sand or remove alignment pins.
Sand Draft Angles
Square Wall edges by sanding draft angles. Edges to be sanded are marked "A" (Fig. 3).
1. Sand both edges of Side Wall (513-4) and left edge of Back Wall (513-3).
2. Tack a piece of 120-grit sandpaper to a board, then sand evenly until wall edges are square.
Turret Window Panels
1. Remove Turret Window Panels (5x) from sprue and clean as noted above.
2. Carefully, glue window Panels together in illustrated order (Fig. 1). It is important that the
windows are correctly aligned. Set aside to dry.
NOTE: Turret Window Panels are assembled as a unit and attached to the building at a later step. For
assembly purposes, the backside of a Panel is marked "0" and another is marked "00". The Panel
marked "0" will attach to Wall (513-2) and panel marked "00" will attach to Wall (513-1) (Fig. 3).
Turret Window Panels must be assembled in the proper order.
Attach Corner Block to Roof
1. Roof will be placed with the rolled roofing side up. Use a hobby knife to scrape "0" from corner of
Roof (513-8) and "0" from Corner Block (513-7). Face the cutting edge of blade opposite the direction
you scrape as to not cut into the part.
2. Align and glue Corner Block (513-7) to Roof (513-8) in corner previously marked "0" (Fig. 2).
CAUTION: Cutting tools recommended.
Use with care. / ACHTUNG: Schneidwerkzeuge
empfohlen. Mit Vorsicht benutzen.
WOODLAND SCENICS
LANDMARK STRUCTURES
®
N BUILDING KIT
CORNER TURRET BUILDING #51300
MODELING AND CARE INFORMATION This kit suggests the use of
materials that may stain or cause damage. Take care to cover project area
and clothing appropriately. Follow recommendations for use and cleanup.
WOODLAND
Manufactured by
®
Paint Roof
Prime Roof and paint grimy black before installing.
Chimney Backs
1. Glue Chimney Backs (513-13) to molded-in chimney fronts (Fig. 3).
2. When glue is dry, sand tops level.
Wall Assembly Part 1
1. Align Wall (513-4) with alignment pins on Wall (513-3) (Fig. 3). Check seams for alignment and
fit. Although Walls are different heights, the bottom of Walls must be as level as possible.
2. Apply glue along inside seams.
Attach Turret Window Assembly
1. Turn Walls (513-1) and (513-2) and Turret Assembly upside down (Fig. 4). There is a groove in
the edge of the Walls where the Turret Assembly is attached.
2. Align Wall (513-2) with side of Turret Assembly marked "0". Apply glue along seam. Hold until
setting begins.
3. Align Wall (513-1) with Turret Assembly marked "00". Apply glue along seam. Hold until setting
begins. Be sure top of Turret Assembly and top of Walls (513-1) and (513-2) are flush and aligned
with each other.
NOTE: A squaring block with 90° angle is useful with this step of assembly.
Install Door
From the inside, place Door (513-12) in opening and glue in place (Fig. 4 insert).
Wall Assembly Part 2
Using alignment pins as a guide, glue Wall Assembly (513-3 and 513-4) to Wall and Turret Assembly
(513-1 and 513-2). Keep bottom of walls level. Let dry.
Roof Installation
1. From the top of the building, slide Roof (513-8) under Chimney Backs (513-13) (Fig. 5). If Roof
does not fit, sand edge(s) as needed.
2. Roof should set snug against bottom of Chimney Backs. Top of Corner Block should set flush with
top of adjoining Walls (513-1 and 513-2) (Fig. 5 inset). If necessary, sand slightly to level.
3. Glue Roof from underneath. Let dry.
Model making product. Not a toy! Not suitable for children under 14 years! / Produit pour le modélisme. Pas un
jouet! Pas adapté aux enfants de moins de 14 ans! / Producto para modelismo. No es un juguete! No adecuado
para niños menores de 14 años! / Modellbauartikel. Kein Spielzeug! Nicht geeigent für Kinder unter 14!
® • PO BOX 98, LINN CREEK, MO 65052 • N2 • woodlandscenics.com
®