FeinTech LAL00110 Bedienungsanleitung

LAL00110 LED work light 10 W rechargeable
LAL00120 LED work light 20 W rechargeable
Safety Information
ƒ Read the operating instructions carefully before using the lamp.
ƒ Do not use if the lamp or the power adapter are damaged – danger to life!
Contact a qualified electrician or our service department.
ƒ Do not look directly at the lamp.
ƒ Do not use the lamp in potentially explosive atmospheres – danger to life!
ƒ The lithium battery inside is replaceable.
ƒ Bulb or. LED chips are not to be replaced
ƒ Drain the battery completely and charge before using the lamp for the first time.
ƒ The lamp can be used while recharging (2A charger power recommended).
ƒ If the lamp is not used for an extended period of time, it is recommended that
the battery is charged every 3 months.
Delivery content:
LED work light, USB charging cable, manual
Charging:
Connect an 5 V USB charging device  with the provided USB cable  to the connector
of the work light . Make sure the charger has a loading power of at least 1A. For faster
charging we recommend 2A power.
Battery indicator:
The battery status is displayed by 4 LEDs . While charging, LEDs are blinking. When
battery is fully loaded, all 4 LEDs are lit. When battery is low, one LED is lit.
Control:
The lamp is switched ON/OFF by using the super touch switch . It will switch into
dimmable function when you press it for a long time. The brightness will go down and
up as one cycle.
Protection:
The lamp is suitable for indoor and outdoor use according to IP54 (protection against
dust ingress and splashing of water). Dust, rain and water splashing against the enclo-
sure from any direction shall have no harmful effect. The lamp is not protected against
powerful water jets and complete immersion in water!
Dispose
Do not dispose of electrical appliances and rechargeable batteries with your household
rubbish. Waste electrical and electronic devices contain valuable raw materials that can
be recycled. Rechargeable batteries are classified as hazardous waste. They must be
collected separately from general waste to be recycled in an environmentally compatible
manner. Check with your Local Authority or Retailer for recycling facility and advice.
Conformity
The product complies with the legal requirements, in particular the EU regulation of
restricted substances and the Electromagnetic compatibility (EMC) Directive. It has
been tested according to EN 55015:2013 and EN 61547:2009. The requirements of
Directive 2011/65/EU (RoHS) and 2015/863/EU are complied. Please contact us
for a formal declaration of conformity or visit our website www.feintech.eu.
www.feintech.eu
FeinTech is a registered trademark of Spreewald Kommunikationstechnik GmbH
Radensdorfer Hauptstraße 45 a, 15907 Lübben (Spreewald), Deutschland
Overview
 Supertouch switch, power on/off and dimming
 Battery status indicator
 Charging port USBmicro
 USB Charger (not included) for connection to the mains
 USB cable

FeinTech LAL00120
20W • DC 5V • 8800 mAh
SKT GmbH • Radensdorfer Hauptstr. 45 a
15907 Lübben (Spreewald) • Germany
IP54


LAL00110
maximum light power 700 lumen
power 10 W
light source 9 x SMD2835 LED chip
colour temperature CCT 4000 K
CRI >80 Ra
beam angle 120°
battery (Lithium-Ion) 3.7V, 4400 mAh
charging time 3.5 h (@ 1A adaptor)
charging voltage 5 V
operating time >2 h max. brightness,
>18 h max. dimmed
Working temperature -5° – +40°C
LED lifetime > 30.000 h


(not included)
LAL00120
1400 lumen
20 W
20 x SMD2835 LED chip
4000 K
> 80 Ra
120°
7.4 V, 8800 mAh
3.5 h (@ 2A adaptor) or
7 h (@ 1A adaptor)
5 V
>2,5 h max. brightness
>20 h max. dimmed
-5° – +40°C
> 30.000 h