Cotech IPC15A1A Bedienungsanleitung

LED Floodlight
Art.no 36-7018, 36-7019, 36-7025, 36-7026
Model IPC15A1A, IPC15A1A-W, IPC30SA1A-B, IPC30SA1A
Please read the entire instruction manual before use and then save it for
future reference. We reserve the right for any errors in text or images and any
necessary changes made to technical data. In the event of technical problems or
other queries, please contact our Customer Services.
Safety
• This product is extremely bright. Do not look directly into the light, doing so
could cause eye damage.
• Never let children play with the product.
• The product must only be connected to a power supply of 230 V with
a protective earth.
• The product must not be used in rooms where explosive gases or liquids are
used or stored.
• Treat the product with care and do not subject it to shocks or impacts.
• Never immerse the product in water or other liquid.
• The product must not be covered.
• Never try to open the housing, repair or modify the product in any way.
• Never use the product if your hands are moist or wet.
• Never use the product if it, its mains lead or plug is damaged in any way.
• All repairs must be carried out by qualified service technicians using genuine
spare parts.
• The mains lead should be checked regularly. If the mains lead is damaged in
any way it must be replaced by a qualified electrician.
Installation
• This floodlight is intended for permanent installation and should only be
installed by a qualified electrician.
• Fasten the floodlight to a firm, level surface.
• Do not mount the floodlight where there is a risk of it falling into water or
other liquids.
Warning
• Make sure that the wall has no concealed electrical wiring, gas or water
pipes before drilling/screwing.
• Make sure that the power supply to the floodlight is switched off/isolated.
• The floodlight should be connected to a power supply protected by a safety
device such as a residual current circuit breaker/residual current device
(RCCB/RCD).
The LED module in the light fitting must not be replaced by anyone other
than a qualified electrician.
1. Use the wall bracket as a template
and mark out where the screw holes
are to be drilled.
Note: You don't need to detach
the wall bracket from the floodlight,
it pivots to make it easier to mark
out holes for drilling and screwing in
mounting screws.
GREAT BRITAIN • CUSTOMER SERVICE tel 020 8247 9300 e-mail customerservice@clasohlson.co.uk internet www.clasohlson.co.uk postal 10 – 13 Market Place, Kingston Upon Thames, Surrey, KT1 1JZ
2. Use an appropriate type of screw for the wall material and attach the bracket
to the wall.
3. The floodlight has 50 cm mains connection cable. It should be connected to
a watertight connection box (sold separately) with a strain relief (as pictured).
4. Use the connection box as a template and mark out where the screw holes
are to be drilled.
5. Use an appropriate type of screw for the wall material and attach
the connection box to the wall.
6. Connect the three wires in the mains connection cable: L Live (brown),
N Neutral (blue) and Protective Earth (green/yellow), to the corresponding
coloured wires of the mains power supply cable.
7. Tilt the floodlight to the desired angle
and tighten the screws fastening
the wall bracket to the floodlight.
Care and maintenance
Clean the floodlight by first switching it off and then wiping it with a dry cloth.
Important
If the glass on the front of the floodlight is damaged, it must be replaced before
the floodlight is used again. The floodlight must not be used if the glass is
damaged or missing.
Responsible disposal
This symbol indicates that this product should not be
disposed of with general household waste. This applies
throughout the entire EU. In order to prevent any harm to
the environment or health hazards caused by incorrect
waste disposal, the product must be handed in for recycling
so that the material can be disposed of in a responsible
manner. When recycling the product, take it to your local
collection facility or contact the place of purchase. They will
ensure that the product is disposed of in an environmentally
sound manner.
Specifications
36-7018
220–240 V AC, 50/60 Hz
Rated voltage
Power 15 W
Colour Black
COB-LED, 1270 lm (non-replaceable)
Light source
Colour temperature 4000 K
Colour rendition > 80 Ra
Beam angle 120°
IP rating IP65
Protection class Class 1 (the product must be earthed)
Operating temperature −20 to 40 °C
Connecting cable 50 cm, H05RN-F3G1.0 mm²
15 × 12 × 4.2 cm
Size
36-7019
Rated voltage 220–240 V AC, 50/60 Hz
15 W
Power
Colour White
Light source COB-LED, 1270 lm (non-replaceable)
Colour temperature 4000 K
Colour rendition > 80 Ra
Beam angle 120°
IP rating IP65
Protection class Class 1 (the product must be earthed)
Operating temperature −20 to 40 °C
Connecting cable 50 cm, H05RN-F3G1.0 mm²
Size 15 × 12 × 4.2 cm
36-7025
Rated voltage 220–240 V AC, 50/60 Hz
Power 30 W
Colour Black
Light source COB-LED, 2550 lm (non-replaceable)
Colour temperature 4000 K
Colour rendition > 80 Ra
Beam angle 120°
IP65
IP rating
Protection class Class 1 (the product must be earthed)
Operating temperature −20 to 40 °C
Connecting cable 50 cm, H05RN-F3G1.0 mm²
Size 17.5 × 14.5 × 5 cm
36-7026
Rated voltage 220–240 V AC, 50/60 Hz
Power 30 W
Colour White
Light source COB-LED, 2550 lm (non-replaceable)
Colour temperature 4000 K
> 80 Ra
Colour rendition
Beam angle 120°
IP rating IP65
Protection class Class 1 (the product must be earthed)
Operating temperature −20 to 40 °C
Connecting cable 50 cm, H05RN-F3G1.0 mm²
Size 17.5 × 14.5 × 5 cm