eKids iSF-12VM Bedienungsanleitung

This product bears the selective sorting symbol for waste electrical and electronic equipment (WEEE).
This means that this product must be handled pursuant to European Directive 2012/19/EU in order to be recycled
or dismantled to minimize its impact on the environment.
For further information, please contact your local or regional authorities.
Electronic products not included in the selective sorting process are potentially dangerous for the environment
and human health due to the presence of hazardous substances.
WARNING:
• Do not ingest the battery, Chemical Burn Hazard. This product contains a coin/button cell battery. If the coin/button
cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
• Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the
product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of
the body, seek immediate medical attention.
• WARNING: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. REPLACE ONLY WITH
THE SAME OR EQUIVALENT TYPE. DO NOT DISPOSE OF BATTERIES IN THE HOUSEHOLD TRASH OR FIRE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
Maintenance
It is important to keep the unit as dry and clean as possible. Unplug the unit, then clean the unit with a damp cloth. Stronger
cleaning agents, such as thinner or similar materials are not recommended, as they may damage the surface of the case.
Questions or Comments
For questions or comments regarding this or other eKids products, please visit our website: www.ekids.com
Getting Started:
Connect one end of the included USB power cable to the LED light strip, making sure Pin 1 on each are aligned.
Connect the other end of the USB cable to a powered USB port.
USB Adaptor
(not included)
OR
Computer connected
to working outlet
Replacing the Batteries
ATTENTION: Batteries should only be installed by an adult.
The remote comes with a CR2025 battery already installed.
To replace the batteries at home, follow these instructions:
1. Follow the diagram on the back of the remote control to open the battery compartment door.
1
2. Install one CR2025 size battery into the compartment, making sure that the + and -
3. Close the battery compartment door.
2
3
For proper disposal of used batteries, please check with your local authorities.
KEEP USED BATTERIES AWAY FROM SMALL CHILDREN.
Adhesive Strip:
Important
• Apply power to test LED Light Strips before mounting.
• The backing tape on LED Light Strips is coated with a strong adhesive that is intended for a single
application only. Apply only when a lighting location is fully determined.
1. Remove the paper lining from the LED light strip to expose the adhesive.
2. Press firmly to mount the LED light strip on a dry, clean, flat surface.
Remote Control
Brightness
RGB Color Modes
Remote Functions:
Use the remote control to adjust colors, brightness, and light modes.
Colors: Press the color buttons to cycle through hues of Red, Green, and Blue. Press the W Button for white light.
Brightness: Use the Brightness Buttons to select High or Low.
Light Modes: Flash, Strobe, Fade, Smooth
Important Safety Information:
Before installing, read and follow all precautions, including the following:
CAUTION: RISK OF ELECTRIC SHOCK OR BURNS - USE IN A DRY LOCATION ONLY
WARNING: The LED strip must be unplugged when making any modifications to the device.
LED Light Strip Handling:
• Do not place in reach of children.
• Do not stare directly into LED lights when illuminated.
• Always disconnect power supply before cutting/connecting LED Light Strips.
• Do not expose LED Light Strips' to direct or indirect moisture.
• For indoors use only.
• For optimum performance connect to a 5v 1A USB adapter.
• Keep away from curtains and other combustible materials
• Do not use if there is any damage to the light or cord insulation. Inspect periodically.
© 2020 eKids, LLC
PO Box 2228, BELFAST, BT5 9GD
contact@support.ekids.com
LED Light Strip with Remote
Model: iSF-12VM
Computer USB port
polarities match the diagram printed inside.
OFF/ON
Modes
White Light
Light Modes
ENG