Herunterladen Diese Seite drucken

Werbung

FL05, FL10
Installation instructions I Consignes d'installation I Montageanleitung
220-240V AC I 50-60Hz
LIVE - L (F) BROWN
NEUTRAL - N (N) BLUE
EARTH - E
YELLOW / GREEN
220-240V AC I 50-60Hz
PHASE - L (F) MARRON
NEUTRE - N (N) BLEU
TERRE - E
VERT / JAUNE
220-240V AC I 50-60Hz
PHASE - L (F) BRAUN
NEUTRAL - N (N) BLAU
ERDE - E
GELB / GRÜN
EN
Installation
1. Set required colour temperature for all units. Switch is
located at the back of the floodlight under rubber cover.
Use small screwdriver to lever the cover to access the
switch.
Note: Ensure the rubber cover is fitted correctly after
selecting the colour temperature.
2. Fix the circular wall bracket to the wall. Screws and wall
plugs are supplied.
3. Locate the floodlight over the circular wall bracket and
tighten the screw to secure it in the required position. The
aim of the floodlight can be adjusted by turning/tilting
the unit.
4. Connect the flying lead to the mains supply. A suitable
waterproof junction box or enclosure must be used to
maintain the IP65 rating of the product.
5. Tighten the two side screws to clamp the floodlight in the
required position.
Note: When the floodlight is switched on for the first time,
you may notice a slight presence of condensation behind the
glass.
The product is fitted with a breathable gland and any
condensation will disappear after several hours of use.
Installation data
Isolate the mains supply, prior to wiring.
This unit must be wired by a qualified electrician or
suitable competent person.
The light source of this luminaire is not replaceable.
When the light source reaches it's end of life the whole
luminaire shall be replaced.
5 year warranty
5 ans de garantie
5 Jahres-Garantie
t +44 (0) 1604 495 151 f +44 (0) 1604 495 095 e sales@collingwoodgroup.com w collingwoodlighting.com
EN
Collingwood Lighting, Brooklands House, Sywell Aerodrome, Sywell, Northampton NN6 0BT, United Kingdom
t +33 (0) 4 816 816 10 f +33 (0) 4 816 816 11 e ventes@collingwoodgroup.com w collingwoodlighting.com
FR
Collingwood Lighting Limited, 43-47 Avenue de la Grande Armée, 75 116, Paris, France
L E N
FR
Installation
1. Réglez la température de couleur requise pour tous les
produits. L'interrupteur est situé à l'arrière du projecteur
sous un cache en caoutchouc. Utilisez un petit tournevis
pour soulever le couvercle pour accéder à l'interrupteur.
Remarque: assurez-vous que le couvercle en caoutchouc
soit correctement remis en place après avoir sélectionné
la température de couleur.
2. Installez le support mural circulaire au mur. Les vis et les
chevilles sont fournies.
3. Placez le projecteur sur le support mural circulaire et
serrez la vis pour le fixer dans la position souhaitée.
L'orientation du projecteur peut être ajustée en tournant /
inclinant l'appareil.
4. Connectez le câble au secteur. Une boîte de connexion ou
un boitier étanche doit être utilisé afin de maintenir l'IP65
du produit.
5. Serrez les 2 vis sur les côtés pour maintenir le projecteur
dans la position requise.
Remarque: Lorsque le projecteur est allumé pour la
première fois, vous pouvez remarquer une légère présence
de condensation derrière la vitre.
Le produit est équipé d'un presse étoupe respirant qui
permet d'évacuer l'essentiel de l'éventuelle condensation
après quelques heures de fonctionnement.
Données d'installation
Isolez l'alimentation secteur avant le câblage
Cet appareil doit être installé par un électricien qualifié
ou une personne compétente appropriée.
La source lumineuse de ce luminaire n'est pas
remplaçable. Lorsque la source lumineuse atteint sa fin
de vie, le luminaire complet doit être remplacé.
Ø10mm
DE
Installation
1. Stellen Sie die gewünschte Farbtemperatur für alle
Geräte ein. Der Schalter befindet sich auf der Rückseite
des Scheinwerfers unter der Gummiabdeckung.
Benutzen Sie einen kleinen Schraubenzieher, um die
Abdeckung anzuheben und auf den Schalter zuzugreifen.
Hinweis: Bitte stellen Sie sicher, dass das Gummi nach
der Farbtemperaturauswahl korrekt sitzt.
2. Befestigen Sie die runde Wandhalterung an der Wand.
Schrauben und Dübel werden mitgeliefert.
3. Platzieren Sie den Scheinwerfer über der runden
Wandhalterung und ziehen Sie die Schraube an, um sie
in der gewünschten Position zu fixieren. Die Ausrichtung
des Scheinwerfers kann durch Drehen/Kippen des Geräts
eingestellt werden.
4. Verbinden Sie die freie Zuleitung mit dem Stromnetz.
Um die Schutzart IP65 des Produkts aufrechtzuerhalten
muss eine geeignete wasserdichte Anschlussdose oder
Gehäuse verwendet werden.
5. Ziehen Sie die beiden seitlichen Schrauben fest, um den
Scheinwerfer in der gewünschten Position zu halten.
Hinweis: Beim ersten Einschalten des Strahlers kann es zu
leichter Kondensationsbildung hinter dem Glas kommen.
Das Produkt ist mit einer atmungsaktiven Dichtung
ausgestattet, und etwaige Kondensation bildet sich nach
einigen Stunden Gebrauch zurück.
Installationsdaten
Vor der Verdrahtung Netzversorgung isolieren
Diese Einheit muss von einem qualifizierten Elektriker
oder einer geeigneten kompetenten Person verdrahtet
werden.
Die Lichtquelle dieser Leuchte ist nicht austauschbar.
Wenn die Lichtquelle ihr Gebrauchsende erreicht hat,
muss die gesamte Leuchte ersetzt werden.
CWI 8146 V4

Werbung

loading

Inhaltszusammenfassung für Collingwood Lighting FL10

  • Seite 1 Collingwood Lighting, Brooklands House, Sywell Aerodrome, Sywell, Northampton NN6 0BT, United Kingdom t +33 (0) 4 816 816 10 f +33 (0) 4 816 816 11 e ventes@collingwoodgroup.com w collingwoodlighting.com CWI 8146 V4 Collingwood Lighting Limited, 43-47 Avenue de la Grande Armée, 75 116, Paris, France...
  • Seite 2 Collingwood Lighting, Brooklands House, Sywell Aerodrome, Sywell, Northampton NN6 0BT, United Kingdom t +33 (0) 4 816 816 10 f +33 (0) 4 816 816 11 e ventes@collingwoodgroup.com w collingwoodlighting.com CWI 8146 V4 Collingwood Lighting Limited, 43-47 Avenue de la Grande Armée, 75 116, Paris, France...

Diese Anleitung auch für:

Fl05