Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
7
CD player
To change to the CD player, short press
displays <CD>.The display will read <Reading>, followed by <No disc>,
if the CD compartment is empty.
Play a CD
NOTE: It is not possible to play DVD or computer CDs.
Press
. The CD drawer will open and <Open> will be displayed.
Place CD onto the CD tray. Ensure that the CD is laying flat on the tray.
Press
to close the CD tray. <Reading> will be displayed and after a
short delay, the CD will start playing.
CD controls:
The following controls are possible when playing a CD:
Short press to play a CD. The track number and the elapsed time of
the track will be displayed. Press again to pause the CD. The elapsed time
will flash while music is paused.
Short press to move to next track. Long press to forward within a
track.
Press to move to previous track. Long press to rewind within a track.
Press to stop CD.
NOTE: If you stop or pause playing a CD for approximately 20 minutes,
your micro system will go into standby mode automatically.
Programmed play
Using your remote control, you can program the play order of up to 20
tracks on your CD.
NOTE: To set up programmed play, the CD must be stopped in
the CD compartment and must not be paused or playing.
While in CD mode:
In CD mode, with the CD you wish to programme in the CD
compartment and stopped:
to enter CD programmed play mode <T01 P01> will be
Press
displayed.
Use
or
to go to the track number that you would like to program
to play first. Press
to confirm.
You will now be able to select the second track that you would like to
program. Continue to select each track as above, up to a total of 20
tracks.
Press
to play the programmed tracks.
To exit programmed play mode, press
Caring for compact discs
• Do NOT touch the playback side of the CD.
• Do NOT attach paper or tape or any other material to the disc.
• Fingerprints and dust on the disc will cause sound deterioration. Wipe
the disc from the centre outwards with a soft cloth Always keep the
disc clean.
• If dust or marks cannot be removed with a soft cloth, wipe the disc
lightly with a slightly damp soft cloth and then wipe with a soft dry
cloth.
• Do NOT use any type of solvent, commercially available cleaners or
antistatic spray for vinyl as it may damage the disc.
• Do NOT store discs in a place subject to direct sunlight or near a heat
source.
• Do NOT store discs in a place subject to moisture or dust, such as a
bathroom or near a humidifier.
Bluetooth mode
Ensure your micro system is in Bluetooth mode by short pressing
until the radio displays <Bluetooth>. Your micro system will begin to
until the micro system
twice.
search for Bluetooth devices. Ensure the Bluetooth-enabled device you
are connecting to is discoverable.
NOTE: If necessary, refer to the instructions for
your device to add or set up Bluetooth.
When found, your micro system will be displayed as 'SHARP XL-B520D' on
your device. Select this to begin pairing. Once done, <Connected> will
be displayed on your radio.
Paired devices will connect to the micro system when they are within
range (within 10 metres in line of sight). Your device will remain paired
with the radio unless you decide to disconnect it.
To disconnect from Bluetooth, long press
current device and search for new devices.
Wirelessly stream music via Bluetooth
In Bluetooth mode, you can wirelessly stream audio through the micro
system. Use the controls on your paired Bluetooth device as well as those
on your micro system. Controls available:
• Play/ Pause: Short press
• Previous track: Short press
• Next track: Short press
Volume can also be adjusted – either using your micro system and/or
your connected device.
NOTE: If the micro system is inactive for 20 minutes, or no audio signal
is being received, the micro system will automatically go into standby.
USB mode
Ensure your micro system is in USB mode by short pressing
the micro system displays <USB>.
Insert the USB stick which has the MP3 files you wish to play into the
USB input.
NOTE: If the USB does not insert easily, try rotating it by 180
degrees and try again. Never force the USB stick into the socket or
try to insert it at an angle as this could damage the socket.
NOTE: USB drives up to 64GB FAT32 are supported.
The following controls are available when using a USB:
Short press to Play/Pause.
Short press to move to previous track. Long press to rewind within
a track.
Short press to move to next track. Long press to forward within a
track.
Press to stop.
NOTE: To navigate the folders on the USB, use
and
on the remote control.
Aux in mode
To change to an Aux-input, short press
displays <Aux in>.
Use a 3.5mm audio input connection cable (not included) for a quick and
easy connection to an external audio source.
Connect one end of the 3.5mm audio connection cable to the
headphone (or auxiliary out) socket of your secondary device, connect
the other end to the Aux in socket on the rear of your micro System.
Press the Play button on your external device to start playback through
the micro System speakers.
To gain optimal volume levels, adjust the output volume level on both
the secondary device and on the micro System.
NOTE: It is recommended that you unplug the Audio cable from the Aux
in socket after you have finished listening to your external device.
for 3 seconds to unpair your
until
until the micro system
Werbung
Inhaltsverzeichnis
