Specifications; Additional Safety Rules - Makita 4101RH Betriebsanleitung

ENGLISH
1 Wing bolt
2 Water pipe
3 Hex wrench 5
4 Loosen
5 Tighten
6 Wrench 22
7 Inner flange
8 Diamond wheel
9 Outer flange
10 Hex socket head bolt
11 Base

SPECIFICATIONS

Model
Wheel diameter .................................................. 125 mm
Max. cutting capacities
At 90° .............................................................. 41.5 mm
At 45° ................................................................. 26 mm
No load speed (RPM) ........................................... 12,000
Overall length ..................................................... 236 mm
Net weight .............................................................. 2.9 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. This tool
should be grounded while in use to protect the operator
from electric shock. Use only three-wire extension cords
which have three-prong grounding-type plugs and three-
pole receptacles which accept the tool's plug.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

ADDITIONAL SAFETY RULES

1. This tool is equipped with a portable residual
current device. Do not connect the tool to a
power supply without using the PRCD (Portable
Residual Current Device). In case of damage of
the cord, it has to be replaced by the manufac-
turer's service organization.
2. For additional protection against electric shock,
be sure to WEAR RUBBER GLOVES AND RUB-
BER BOOTS during operation.
3. Check the wheel carefully for cracks or damage
before operation. Replace cracked or damaged
wheel immediately.
4. Use only flanges specified for this tool.
5. Be careful not to damage the spindle, flanges
(especially the installing surface) or bolt. Dam-
age to these parts could result in wheel break-
age.
6. When using the water feed, be careful not to let
water get into the motor. If water runs into the
motor, an electric shock hazard may result.
7. Hold the tool firmly.
8. Keep hands away from rotating parts.
Explanation of general view
12 Wing nut
13 This end of blade case should
be above the red line.
14 Red line
15 "TEST" button
16 "ON" button
17 Pilot lamp
18 Portable residual current device
(PRCD)
19 Switch trigger
20 Lock-off button
9.
4101RH
10. Wait until the wheel attains full speed before cut-
11. Stop operation immediately if you notice any-
12. Do not attempt to lock the trigger in the "ON"
13. Never attempt to cut with the tool held upside
14. Before setting the tool down after completing a
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing water pipe (Fig. 2)
First, unplug the tool. Loosen the wing bolt on the depth
guide and move the base down. Install the water pipe on
the blade case using the screw as shown in Fig. 2.
Attach the vinyl tube onto the water pipe and attach the
adapter on the vinyl tube to a faucet of water mains pres-
sure. Adjust the amount of water flow by simply adjusting
the water cock.
Installing or removing diamond wheel
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the wheel.
Hold the outer flange with the wrench and loosen the hex
socket head bolt in clockwise direction with the hex
wrench. Then remove the hex socket head bolt and outer
flange. (Fig. 3)
Install the diamond wheel, outer flange and hex socket
head bolt onto the spindle. Hold the outer flange with the
wrench and tighten the hex socket head bolt in counter-
clockwise direction with the hex wrench. BE SURE TO
TIGHTEN THE HEX SOCKET HEAD BOLT SECURELY.
(Fig. 4)
CAUTION:
Use only the Makita wrench and hex wrench to install or
remove the wheel.
21 Top guide
22 For straight cuts
23 For 45° bevel cuts
24 Clamp
25 Cover (A)
26 Screw
27 Cover (B)
28 Limit mark
29 Brush holder cap
30 Screwdriver
Make sure the wheel is not contacting the work-
piece before the switch is turned on.
ting.
thing abnormal.
position.
down in a vise. This can lead to serious acci-
dents, because it is extremely dangerous. (Fig.
1)
cut, be sure that the wheel has come to a com-
plete stop.
7